anyone running LEDs on their 7?
#51
Former Moderator. RIP Icemark.
Originally Posted by 86GXL
Just tryin to show they light up most of the lense and can be seen from angles
I even have a LED array for the 3rd brake light that I ahve been trying to make so I can sell it at my webstore... and that is using thirty 10kMCD bulbs... still not enough light comparied to a single conventional 1156 bulb
#52
Locust of the apocalypse
Join Date: Apr 2003
Location: Directly above the center of the earth (York, PA)
Posts: 2,553
Likes: 0
Received 1 Like
on
1 Post
Originally Posted by Icemark
Actually I have a set of Red 1157 19 LED lights sitting on my desk right now that claims to have a 120 degree veiw... but they are not much better and still too little light (other than a nice 1 inch circle on the lens) to be practicle.
Yeah.. i meant to say with a VERY high light output... most of the superbrights i use for projects have a relatively small direct viewing angle..
#53
Locust of the apocalypse
Join Date: Apr 2003
Location: Directly above the center of the earth (York, PA)
Posts: 2,553
Likes: 0
Received 1 Like
on
1 Post
Originally Posted by 86GXL
Never did they say that...
I guarentee a block of LED's will be brighter... Didnt i just prove that with my ONE THOUSAND FOOT study????
I guarentee a block of LED's will be brighter... Didnt i just prove that with my ONE THOUSAND FOOT study????
You were DIRECTLY behind the car weren't you.... what did they look like if you stepped a few degrees off center???? I have no doubt that the leds were brighter at 1000 ft if you were directly in line with them
#54
Originally Posted by Icemark
Again, I want LEDs to work... they just don't.
I even have a LED array for the 3rd brake light that I ahve been trying to make so I can sell it at my webstore... and that is using thirty 10kMCD bulbs... still not enough light comparied to a single conventional 1156 bulb
I even have a LED array for the 3rd brake light that I ahve been trying to make so I can sell it at my webstore... and that is using thirty 10kMCD bulbs... still not enough light comparied to a single conventional 1156 bulb
Last edited by 86GXL; 11-24-04 at 12:21 AM.
#55
Banned. I got OWNED!!!
Join Date: Sep 2004
Location: .
Posts: 160
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Icemark
Again, I want LEDs to work... they just don't.
I even have a LED array for the 3rd brake light that I ahve been trying to make so I can sell it at my webstore... and that is using thirty 10kMCD bulbs... still not enough light comparied to a single conventional 1156 bulb
I even have a LED array for the 3rd brake light that I ahve been trying to make so I can sell it at my webstore... and that is using thirty 10kMCD bulbs... still not enough light comparied to a single conventional 1156 bulb
#56
Originally Posted by YearsOfDecay
You were DIRECTLY behind the car weren't you.... what did they look like if you stepped a few degrees off center???? I have no doubt that the leds were brighter at 1000 ft if you were directly in line with them
#57
Former Moderator. RIP Icemark.
Originally Posted by MakoRacing[FC]
I wonder how LED traffic lights pull it off then, cause I assure you that they are brighter then standard bulbs.
They are not retrofited existing reflective incandescent fixtures for under $100.
And I have never seen a LED traffic light array be brighter than an incandescent. They simply last longer. In fact many traffic light LED arrays often wash out with direct sunlight on the lens.
And as a side bar, my voltage does not drop when my lights are turned on... if yours is, perhaps you need to look at replacing your alt.
But I am done with this subject. Again if you like them use them (LEDs). I don't consider them a safe replacement yet.
Last edited by Icemark; 11-24-04 at 12:35 AM.
#59
Rotary Enthusiast
Join Date: Oct 2003
Location: Wichita, KS
Posts: 1,183
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
David Hayes
3rd Generation Specific (1993-2002)
13
09-05-22 12:45 PM