Rxmfn7

iTrader: (4)

I have yet to remove a set of FTP lenses without the plastic surrounding the studs crumbling.. I am super careful with them, and even press them out with the studs, not the lens itself, and it still breaks. It seems like whenever you loosen that 8mm nut on the inside of the lens, it spins the whole stud a little bit, breaking all of the black plastic surrounding it. Anyone else experience this? This is the 3rd set Ive broken

Zero Cylinder

i know someone has, but i havent, parts car i bought, had a set of used ones in good shape laying in the rear.

jsotelo

I've taken mine out a few times with no problems.. Rarest takes his out almost every time he washes the car.

hpram99

I guess you could try greasing the nuts (haha) before you reinstall your 4th set with some antiseize gunk.

just a posibility

AcidShock

iTrader: (49)

I T-boned a Camaro and my FTP lenses fell out. I just have left them out. But, yeah I know what you are talking about. I tried pulling mine out when I got the car and it was just a no-go because I started hearing crackling sounds from the plastic.

White_FC

Hrmm no...
but, this one time I was braking pretty hard into this corner and one of mine just fell out!!!
then I subsequently ran over it...

I havn't bought any news one just yet, I kind of like the look with them out.

iluvrx7z

When I first bought my FC I was driving and came home and they both fell out while I was driving, putting them in however I felt like I was breaking them.

Dan

n4ji

iTrader: (1)

I love Rarest... what a trooper.

Michael
1988 10AE "Making fun of Rarest 24/7, washing his car or not."

lemonade

just push the screws out from the inside. i did it without breaking them as a "noob"

hybridracer

I took mine out multiple times without breaking them when I had my 90 GTU.

rxspeed87

dude I know it's not really funny but it still gave me a good laugh


but yeah I have taken mine out and have left them out since then
but didn't break anything from them and still able to be put back in at anytime

White_FC

What the hell kinda happy drugs are you on?!

I pissed myself laughing for a good minute after I figured out what actually happend!!

hpram99

I had a good laugh once I read it too. You must have some damn good brakes to shoot them out like that. Or did you actually hit a wall and just don't want to tell us? j/k j/k

White_FC

hehe nahh I did hit a brick wall in my old car though... was was nearly as funny as this.

Nahh stock brakes, just with some bendix ultimate pads in there....
Where the bolts go into the lens was all brittle and just crumbled... (I found that out after I went and picked up the pieces )

jon88se

no trouble with the FTP's, my new JDM's have ben out a couple time, no problems. HOWEVER, tail lights are a different story...a couple studs have popped out the back of each set I've taken off and put back on (S4 to S5, then S5 to my original S4's when I got hit, then BACK to S5 again but 2 sets, first one I got were junk (bad seals). I removed ALL studs from each tail light opn the new S5's I got (close to mint) over the summer, cleaned everything with prepsol and put 5 minute epoxy in each hole before I pressed the studs in (hammer)...I removed these tails a couple times since (used some dynamat to get rid of some lil vibrations) and they've stayed put. Just FYI

Digi7ech

iTrader: (1)

I lost mine because of rear ending someone.

I just went to a junk yard and grabbed them and put them in no problem. I even had to remove them from the scrap car myself.

You just have the headllights up and then twist your hand into the back with a 10mm socket or wrench.

Just ebcareful putting them back in. Don't over tighten it since they are plastic studs.