RX7Club.com - Mazda RX7 Forum

2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:
Banzai Racing

after searching is it true to move pressure sensor vac line on ACV removal?

Thread Tools
 
Search this Thread
 
Old 03-13-04, 03:49 PM
  #1  
1.3L is not that small

Thread Starter
 
cwsttu's Avatar
 
Join Date: Apr 2002
Location: Nacogdoches Tx
Posts: 1,470
Likes: 0
Received 1 Like on 1 Post
after searching is it true to move pressure sensor vac line on ACV removal?
i have a 88 n/a s4 and i have removed the ACV... in the pic below you can see the nipples pointed to in red and the lines that went to them in yellow... but i read somewhere you have to move the pressure sensor line also... which is in blue.. this is where ive always know it to go.. do i need to move it because i have a vac leak somewhere? thanks in advance

cwsttu is offline  
Reply Like
Old 03-13-04, 06:19 PM
  #2  
I'm a boost creep...

 
NZConvertible's Avatar
 
Join Date: Jan 2002
Location: Auckland, New Zealand
Posts: 15,608
Likes: 0
Received 8 Likes on 8 Posts
That's only for turbos, which have the pressure sensor plugged into a nipple on the ACV.
NZConvertible is offline  
Reply Like
Old 03-13-04, 07:23 PM
  #3  
1.3L is not that small

Thread Starter
 
cwsttu's Avatar
 
Join Date: Apr 2002
Location: Nacogdoches Tx
Posts: 1,470
Likes: 0
Received 1 Like on 1 Post
thanks.. just had me confused.. kinda sucks cause i was hoping thats where i messed up and why my car wouldnt idle
cwsttu is offline  
Reply Like
Old 03-13-04, 07:42 PM
  #4  
Like Ghandi with a gun

 
Kenteth's Avatar
 
Join Date: Mar 2003
Location: Rapid City, SD
Posts: 4,584
Likes: 0
Received 0 Likes on 0 Posts
still no idle? me either
Kenteth is offline  
Reply Like
Old 03-13-04, 07:46 PM
  #5  
1.3L is not that small

Thread Starter
 
cwsttu's Avatar
 
Join Date: Apr 2002
Location: Nacogdoches Tx
Posts: 1,470
Likes: 0
Received 1 Like on 1 Post
omg dude im so sick of workin with idle im about to take it to a ******* dealer though i know they wont know ****.. i might tow it to dallas where a guy that works on rotaries is really good
cwsttu is offline  
Reply Like
Old 03-13-04, 09:51 PM
  #6  
Like Ghandi with a gun

 
Kenteth's Avatar
 
Join Date: Mar 2003
Location: Rapid City, SD
Posts: 4,584
Likes: 0
Received 0 Likes on 0 Posts
heh you in east texas near longview?

I dunno, dealer won't know ****, especially with the tb mod, all they will want to do is replace everything...
Kenteth is offline  
Reply Like
Old 03-14-04, 12:04 AM
  #7  
Mazda4Life

 
neptuneRX's Avatar
 
Join Date: Aug 2003
Location: Rockville, MD
Posts: 1,228
Likes: 0
Received 0 Likes on 0 Posts
and charge you out the *** for it too
neptuneRX is offline  
Reply Like

Trending Topics

Old 04-11-04, 07:20 PM
  #8  
Like Ghandi with a gun

 
Kenteth's Avatar
 
Join Date: Mar 2003
Location: Rapid City, SD
Posts: 4,584
Likes: 0
Received 0 Likes on 0 Posts
same nipple set for s5 pressure sensor?
Kenteth is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Installed UIM gasket, now my engine won't run
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
Turbo II brake help. Almost there.
Frisky Arab
2nd Generation Specific (1986-1992)
13
08-18-15 05:30 PM
what's our stock oil sensor thread in the 20b rear iron?
stickmantijuana
20B Forum
8
08-18-15 02:46 PM
Rteck 1.8 questions
eddierotary
2nd Generation Specific (1986-1992)
4
08-16-15 04:12 PM
Back to Subforum
2nd Generation Specific (1986-1992)
View Next Unread
Just put 1000+ miles on my FC TII




Advanced Search
Quick Reply: after searching is it true to move pressure sensor vac line on ACV removal?


Reply Closed Thread Share

All times are GMT -5. The time now is 05:39 PM.