2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

abs warning light, hard pedal

Thread Tools
 
Search this Thread
 
Old Nov 28, 2006 | 10:02 PM
  #1  
brio125's Avatar
Thread Starter
No more 7 for me
Tenured Member 15 Years
 
Joined: Apr 2006
Posts: 377
Likes: 0
From: The Great Country of Texas
abs warning light, hard pedal

so my abs light comes on at random times and goes off at equally random times. sometimes it comes on when i start the car, other times it comes on while braking.

I have noticed a hard brake pedal for a long while now, and i hear the release of pressure from the master slave cylinder just after startup. i have also experienced wheel hop and brake hop, not the abs. I was thinking of rebuilding the pistons and putting in new brake lines along with rotors and pads, but i don't want to spend all that money if it is something small.

does anyone have any suggestions, or other things to look for.

oh...about 2 weeks ago my brake fluid was almost empty, never had a problem before or since. I think this is when the abs light came on first.
Reply
Old Nov 28, 2006 | 10:41 PM
  #2  
sharingan 19's Avatar
Rotary Revolutionary
Tenured Member 15 Years
iTrader: (16)
 
Joined: May 2006
Posts: 3,881
Likes: 3
From: Jacksonville, Tampa & Tallahassee
Watch out, I had problems w/ "dissapearing" brake fluid. A week later the brakes went out going down hill; almost killed my poor 7. It ended up being a bad master cylinder but I'd check the lines very thoroughly first (since they're cheaper)
Reply
Old Nov 30, 2006 | 05:26 PM
  #3  
brio125's Avatar
Thread Starter
No more 7 for me
Tenured Member 15 Years
 
Joined: Apr 2006
Posts: 377
Likes: 0
From: The Great Country of Texas
any other ideas???
Reply
Old Nov 30, 2006 | 05:37 PM
  #4  
cdaleracer669's Avatar
yes,thats me \/
Tenured Member 05 Years
iTrader: (1)
 
Joined: Mar 2006
Posts: 861
Likes: 0
From: Eaton, CO
if its leaking out its probably the master cylinder that NEEDS replaced. replace it before too much drips down the car and eats off the paint, which allows it to rust.
Reply
Old Nov 30, 2006 | 05:43 PM
  #5  
DoriFCto's Avatar
ChaoticControl
Tenured Member 05 Years
 
Joined: Nov 2005
Posts: 140
Likes: 0
From: NC
my 7 is doing the same thing. Found out it was leaky master cylinder. Havent got the chance to put it back together yet but Im 99% sure that was my problem. Definately check all your lines, its tedius but hey it's a 7, also check for any leakage by the bleeders and all connecting points. If you suspect a spot where it is leaking, spray it off with some brake cleaner and dry area. Check it at a later time for any wet spots, trace it to where it came from.
Reply
Old Dec 1, 2006 | 02:27 PM
  #6  
brio125's Avatar
Thread Starter
No more 7 for me
Tenured Member 15 Years
 
Joined: Apr 2006
Posts: 377
Likes: 0
From: The Great Country of Texas
you, know i thought it might be the master cylinder because i can hear a bit of air leaking when i have someone press the brake pedal. i was told that air will escape when the m/c goes bad. i may just get a new one and put it in.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
stickmantijuana
Microtech
30
Apr 23, 2016 06:37 PM
alphawolff
1st Generation Specific (1979-1985)
17
Nov 17, 2015 05:57 PM
fastsaab
New Member RX-7 Technical
5
Aug 19, 2015 11:42 AM




All times are GMT -5. The time now is 03:19 AM.