Wrecked My 7!
#1
Newbie
Thread Starter
Join Date: Sep 2007
Location: INDY
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Wrecked My 7!
i wrecked my 1989 rx7 gtu and basically the whole front end needs replaced.
does anyone know where i could find parts for my car at?
i live in IN and apparently is pretty hard to get parts for an rx7 around here.
<img src=http://i35.tinypic.com/205t5so.jpg><br>
<img src=http://i37.tinypic.com/25tchft.jpg><br>
does anyone know where i could find parts for my car at?
i live in IN and apparently is pretty hard to get parts for an rx7 around here.
<img src=http://i35.tinypic.com/205t5so.jpg><br>
<img src=http://i37.tinypic.com/25tchft.jpg><br>
#4
so you got pistons oh wow
iTrader: (1)
Join Date: Nov 2007
Location: Killeen, Texas
Posts: 900
Likes: 0
Received 0 Likes
on
0 Posts
there is an 87 gxl for 500 bucks arround here. Im not sure if it has a tittle but for what the guy told me he rebuilt the engine and then the tranny took a dump. Im sure it would make a good donor car. pm me and let me know if youre interested so i can try to put you in contact with the guy.
#5
Newbie
Thread Starter
Join Date: Sep 2007
Location: INDY
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#11
Junior Member
Join Date: Apr 2008
Location: rocky mount, NC
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
if it runs and drive, remove the hood and dented panels and get a body kit. Easy lazy fix. Of if you can un-dent the panels, put a widebody kit on it... if they make one.
Last edited by hvguy; 07-30-08 at 05:11 PM. Reason: *
#13
Full Member
Join Date: Mar 2007
Location: hackensack,NJ
Posts: 135
Likes: 0
Received 0 Likes
on
0 Posts
you could get part of a JDM front clip..that comes with bumper radiator support fenders and hood..well sometimes the hood doesn't come with it...their like 350 or so ..i think they have one on ebay...but good luck with that...u should check a body shop that does the frame work too.
#14
Clean.
iTrader: (1)
You're lucky man. That all looks replaceable. The only really bad part will be frame damage, if there is any.
Yeah, try a junkyard. Aftermarket stuff is thin metal and new stuff is way too expensive. After that leave it as-is. If there's any rust, sand it off and prime it with cheap primer, then sand smooth if you want. If you can only find pieces with some dents, hunt down a slapper (curved metal thing, "slaps" b/c it's wide) and hit until it's nearly flat, within 1/8" of perfect. Very easy and doesn't take much precision if you use a slapper instead of a hammer. Sand off the paint on & near the dent, bondo and sand to get it totally flat. Then prime it. For any painting beyond that, most people are best off going to a body shop. Unless you want to make a huge project out of it.
Yeah, try a junkyard. Aftermarket stuff is thin metal and new stuff is way too expensive. After that leave it as-is. If there's any rust, sand it off and prime it with cheap primer, then sand smooth if you want. If you can only find pieces with some dents, hunt down a slapper (curved metal thing, "slaps" b/c it's wide) and hit until it's nearly flat, within 1/8" of perfect. Very easy and doesn't take much precision if you use a slapper instead of a hammer. Sand off the paint on & near the dent, bondo and sand to get it totally flat. Then prime it. For any painting beyond that, most people are best off going to a body shop. Unless you want to make a huge project out of it.
Thread
Thread Starter
Forum
Replies
Last Post
hurleyboi514
2nd Generation Specific (1986-1992)
6
02-01-02 11:05 AM