flipside27

Im doing some graphic work for a client who just happens to be an excellent welder. Given the economic times especially here in MI, he wants to barter and Im willing to do it.

My question is what exactly should I get done? I have a 10AE and its currently a weekend driver.

Some of his work



what do you guys think?

SirCygnus

iTrader: (1)

exhaust and front mount ic.

90FC

Have him build you a roll bar.

Grip

iTrader: (9)

stitch weld the chassis, cage, exhaust, V-mount.

need RX7

iTrader: (4)

V-mount ! Or possibly some small rust repair (if any).

WingsofWar

V-mount, you wont regret it.

Unless you get into an accident, and a roll cage would have saved you from being a paraplegic ...then you can regret it

flipside27

Im definitely thinking about a full custom exhaust or stitch weld.

LOL yeah Wings, that would suck pretty hard

1SWEET7

iTrader: (1)

Front lower bar, custom strut tower bars.

Chaotic_FC

.

TwEaK

iTrader: (6)

my vote is for a roll cage..

rotordad

I would say cage or exhaust.

Rob XX 7

iTrader: (8)

he said $500, some suggestions are alot more then $500, lol

weekend driver and its a 10th I say a nice bolt on part like a strut bar.

Monkman33

iTrader: (28)

Strut bars are about 25 minutes worth of welding time (including clean up ;-) ), unless you are talking a four point strut bar that has two additional attachment points on the firewall?

Otherwise, you are pretty much at an in between point. You are closer to a roll cage than a strut bar.

patman

iTrader: (3)

it depends what other fabrication capabilites he has. Does he have a tubing bender? Mandrel Bender? Does he have a brake?

Fabrication is typically $50-70/hr depending on what he is doing and the size of his shop.

A set of strut bars isnt a bad idea, but if hes does have the equipment, a roll bar would be a good one as well.

need RX7

iTrader: (4)

Divided T4 tubular manifold .

WingsofWar

Stripper pole

Nick_d_TII

iTrader: (6)

A Submarine. A Golf club. And a medieval helmet.

need RX7

iTrader: (4)

47-point roll cage. Every street car needs one.

SirCygnus

iTrader: (1)

why the **** would anyone pass up a full exhaust over a ****** strutbar?

Rob XX 7

iTrader: (8)

the guy may not do exhaust, not all welders will get involved in that.

And no welder around here would charge $500 for a cage, they would laugh at you for that price.

Check out TT's strut bar, that took alot longer then 25 minutes to fabricate https://www.rx7club.com/showthread.p...ighlight=strut

dudes will not touch a SS manifold for under $1200 around here

stevensimon

iTrader: (11)

this

flipside27

^^^ i can probably only get one of those done.
Im lovin the suggestions so far, but I dont know if he has a pipe bender.
I'm going to call him up tomarrow afternoon with my decision so im going to be stalking this thread tonight

Hypertek

iTrader: (3)

something good and custom.. intercooler setup sounds nice, always requires custom piping.

would be stupid to have him make some strut bars that you can easily buy for a hundred lol.

rotordad

A local guy here will do a cage for $500, besides alot of companies sell 4 points for around $500 (AutoPower). Rob sounds like the guys in you area are high priced. I would laugh back & take my buisness else where.

Hypertek

iTrader: (3)

you could get some trick suspension pieces made up


just to get an idea.. They can be made, metal yards usually have the rods and joints with the weld on sleeve or whatevers.

or like some under car chassis braces