Anybody got $48,000?
Thread Starter
Joined: Jun 2006
Posts: 4,815
Likes: 24
From: Columbia, Tennessee
Anybody got $48,000?
Check this out...
Your not ballin' enough unless you put this $48,000 20b in your FC!
http://www.racingbeat.com/FRmazda1.htm
Your not ballin' enough unless you put this $48,000 20b in your FC!
http://www.racingbeat.com/FRmazda1.htm
Trending Topics
@ pipnorcali
Joined: Jan 2004
Posts: 2,751
Likes: 1
From: Grass valley, ca
3-Rotor Race Engine
Racing Beat currently has available for sale a very rare Peripherally Ported, Mazda Race 13G 3-Rotor engine in Racing Beat-engineered, single turbocharger configuration.
The engine is a complete Racing Beat built package producing more than 1000 bhp at 8500 RPM with approximately 21 pounds of boost. Designed to run on methanol, thereby eliminating the need for an intercooler, the race engine package incorporates an EFI Systems Engine Management System supported by a Kinsler Fuel Injection gear-rotor mechanical fuel injection pump. As prepared by Racing Beat, the engine features a complete Peterson Fluid Systems 4-stage oil scavenging assembly. Additionally, the engine utilizes an HPD water pump mounted to a Racing Beat-designed, cast aluminum front cover. These race-proven Kinsler, Peterson, and HPD components are all Gilmer belt-driven peripherals. The turbo charger selected for thes package is the AirResearch T18A90 series with the M-4 compressor wheel. As equipped by Racing Beat, the turbocharger features a TIAL Waste Gate modified to minimize boost spikes.
Internally, the engine includes the following features:
- All tension bolts fully "pinned"
- Water jacket modification on all rotor housings
- Iannetti Ceramic Apex Seals 3mm
- 7.5 to 1 Low-compression ratio rotors, cast by Mazda Japan
- Exhaust manifold - Inconel 625, including all bellows.
For more information or specifications, contact Racing Beat and ask for Jim Tanner at 714-779-8677.
Racing Beat currently has available for sale a very rare Peripherally Ported, Mazda Race 13G 3-Rotor engine in Racing Beat-engineered, single turbocharger configuration.
The engine is a complete Racing Beat built package producing more than 1000 bhp at 8500 RPM with approximately 21 pounds of boost. Designed to run on methanol, thereby eliminating the need for an intercooler, the race engine package incorporates an EFI Systems Engine Management System supported by a Kinsler Fuel Injection gear-rotor mechanical fuel injection pump. As prepared by Racing Beat, the engine features a complete Peterson Fluid Systems 4-stage oil scavenging assembly. Additionally, the engine utilizes an HPD water pump mounted to a Racing Beat-designed, cast aluminum front cover. These race-proven Kinsler, Peterson, and HPD components are all Gilmer belt-driven peripherals. The turbo charger selected for thes package is the AirResearch T18A90 series with the M-4 compressor wheel. As equipped by Racing Beat, the turbocharger features a TIAL Waste Gate modified to minimize boost spikes.
Internally, the engine includes the following features:
- All tension bolts fully "pinned"
- Water jacket modification on all rotor housings
- Iannetti Ceramic Apex Seals 3mm
- 7.5 to 1 Low-compression ratio rotors, cast by Mazda Japan
- Exhaust manifold - Inconel 625, including all bellows.
For more information or specifications, contact Racing Beat and ask for Jim Tanner at 714-779-8677.
![Tyler [S5 FC]'s Avatar](https://www.rx7club.com/customavatars/avatar115591_1.gif){kind=avatar}
Junior Member
Joined: Mar 2008
Posts: 32
Likes: 0
From: Durham, NC
Why not educate me on why? I've never driven or owned a FD..
Seriously? what would be the point? for 48k I better be making 2000hp... you could buy a blown 20b... rebiuld it with a large street port mate it with a gt45r and make 1000hp with all the goodies for around 15-20k....
Chris
Chris
Thread
Thread Starter
Forum
Replies
Last Post
NoFear99
3rd Generation Specific (1993-2002)
43
Jun 13, 2005 09:49 AM
