Updated pics of my 20b FD install
#2
Glutton for Punishment
Thread Starter
iTrader: (1)
Join Date: Dec 2001
Location: MN
Posts: 722
Likes: 0
Received 0 Likes
on
0 Posts
As you can see my install is finnaly back underway. IT has been on hold for a few months while I waited for my Un orthodox/ Tilton Dual Disk clutch. I wish i had my camera when i was assembling the clutch. They did a nice job. I like the new slave cylinder/ Release bearing combo. It fits right over the input shaft, and from what I can tell it is only a little firmer petal feel than stock.
#6
Glutton for Punishment
Thread Starter
iTrader: (1)
Join Date: Dec 2001
Location: MN
Posts: 722
Likes: 0
Received 0 Likes
on
0 Posts
It is a Pettit Subframe & spindles, I bought them from Red-RX7 A while ago before he sent his car to MVA. Everything fits well so far. Unfortunatly I just found out I am headed to Scottsdale, AZ for a couple weeks on Sun. I was hoping to have it rinning with in a week or two.
#7
Rotor Head Extreme
iTrader: (8)
Ahhhh so your the one who bought the sub-fram and spindles from Red-Rx7 Ha! ha! ha! Well, I got everything else except the intercooler. I start my swap next month. Buy the way, what intercooler are you planning on using. Also are you going to keep the twins or go single?
Trending Topics
#9
Glutton for Punishment
Thread Starter
iTrader: (1)
Join Date: Dec 2001
Location: MN
Posts: 722
Likes: 0
Received 0 Likes
on
0 Posts
Stock turbos for a while, I need to buy a house. I have the Greddy 3 row intercooler, but the way greddy mounts the radiator it hits the main pully. I'm fabbing up some new mounting brackets to mount it more vertical. Every thing is going smooth. I bought a used downpipe from Derrick (3rotorrx7.com) after he went single. I'll put some more pics up on Sat.
#11
Rotor Head Extreme
iTrader: (8)
Originally posted by IronMdnX
t-von :
Did you get the swaybar spacers from Mike? If so could you shoot me a picture. I want to see if i can fab something simular.
t-von :
Did you get the swaybar spacers from Mike? If so could you shoot me a picture. I want to see if i can fab something simular.
No I didn't. Sorry I bought the radiator,top&bottom cover trays,throttle body attachment, and fans. I forgot about the swaybar spacers. Oh well! By the way, I don't know how to display pics. Need some help there. How funny we could help each other.
Oh I forgot to ask, why didn't you buy the twin turbo outlet pipes from Derrick "3rotorrx7.com" as well? I may purchase them myself.
#12
Glutton for Punishment
Thread Starter
iTrader: (1)
Join Date: Dec 2001
Location: MN
Posts: 722
Likes: 0
Received 0 Likes
on
0 Posts
I just test fitted the swaybar, I didn't have any interferance issues with the tie rods. I didn't know Derrick was selling the turbo pipes, I just emailed him a long time ago about the DP, I figured i would make my own pipes. I might contact him to see what he wants for them. I finished installing the new oil coolers & oil thermostat. I have the radiator positioned now where i want it, all i need to do is make new lower brackets and mount the A/C condenser on it. Fuel system is about finished I just need to pick up a couple more AN fittings. Watter Pump will be here Mon., I wish i could get out of going to AZ for the 2 weeks.
Thread
Thread Starter
Forum
Replies
Last Post