1st Generation Specific (1979-1985) 1979-1985 Discussion including performance modifications and technical support sections

wierd engine miss

Thread Tools
 
Search this Thread
 
Old Aug 8, 2004 | 07:45 AM
  #1  
SSRx7's Avatar
Thread Starter
Como Frejoles?
Tenured Member 10 Years
 
Joined: Jul 2004
Posts: 615
Likes: 0
From: Jacksonville, Fl
wierd engine miss

Here is one for you guys. Normal driving, engine runs up fine. But if I take a freeway on ramp at speed, soon as I get on the freeway, she starts cutting out. If I swerve to the right a little bit she goes dead, but as soon as I swerve back to the left a little, she comes on at full power.

I know that my elec throttle positioner or controler or whatever that thing is, is out of adjustment, because she starts cutting out at about 5500 rpm in 3rd, 4th, or 5th gear. If I just ease it down , she'll pull strong..... at least until I take a high speed freeway on ramp......

Anyone got any ideas??
Thanks,
Later,
Bill
Reply
Old Aug 8, 2004 | 07:12 PM
  #2  
mwatson184's Avatar
holley guy
Tenured Member 10 Years
 
Joined: Feb 2003
Posts: 898
Likes: 1
From: K.C. MO
Could you give a little more info on the car. Year, model, mods...

Marques
Reply
Old Aug 8, 2004 | 07:40 PM
  #3  
aarsudstrike's Avatar
Junior Member
Tenured Member 05 Years
 
Joined: Jul 2004
Posts: 19
Likes: 0
From: tulsa, ok
have u tried the fuel filter i know it sounds ironic but hey it seems to b a common problem these days and umm u may wanna just try to get your tps readjusted that my fix it also look fo loose connections and such
Reply
Old Aug 9, 2004 | 05:26 AM
  #4  
SSRx7's Avatar
Thread Starter
Como Frejoles?
Tenured Member 10 Years
 
Joined: Jul 2004
Posts: 615
Likes: 0
From: Jacksonville, Fl
Sorry about not posting the info. It is an 85 GS, 12A. I think that it definately has to be in the ignition system because it is to precise of a cut out. I was just wondering if anyone else had the same thing happen. Thanks for the tip on the filter, it has already been replaced. I know that the carb has a funky tps on it, I just have to figure out how it works. Thanks for the replies.
Later,
Bill
Reply
Old Aug 9, 2004 | 11:54 AM
  #5  
Kentetsu's Avatar
Lives on the Forum
Tenured Member 15 Years
 
Joined: Jun 2004
Posts: 11,359
Likes: 14
From: Grand Rapids Michigan
Is it possible that one of your floats are out of adjustment? Maybe you are loosing your gas due to the G-force of the turns emptying the float bowls out.

If you can run it flat out in a straight line without this problem, then you can rule out the fuel filter, pump, etc. If it only happens during (or right after) a hard turn, then I would guess it may be your floats. Good luck!
Reply
Old Aug 12, 2004 | 09:49 PM
  #6  
SSRx7's Avatar
Thread Starter
Como Frejoles?
Tenured Member 10 Years
 
Joined: Jul 2004
Posts: 615
Likes: 0
From: Jacksonville, Fl
Thanks Kentetsu. I have noticed that I smell gas after hard cornering. I guess I'll have to give in and finally take that carb apart. Oh, how I wish it were as easy as a Holley 650.
Well maybe this weekend.
Thanks again.
Later,
Bill.
Reply
Old Aug 12, 2004 | 10:32 PM
  #7  
Kentetsu's Avatar
Lives on the Forum
Tenured Member 15 Years
 
Joined: Jun 2004
Posts: 11,359
Likes: 14
From: Grand Rapids Michigan
You might want to get RX7Carl's opinion before you start tearing in. I was hoping he'd post his thoughts, but don't see him. Just a thought, you might want to PM him for a 2nd opinion. Good luck!
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
befarrer
Microtech
3
Aug 22, 2015 05:52 PM
gtcd
1st Generation Specific (1979-1985)
30
Aug 19, 2015 02:44 AM
Wolf_
Single Turbo RX-7's
3
Aug 11, 2015 04:23 PM




All times are GMT -5. The time now is 12:01 AM.