series3 dash go into a series1?
#1
Junior Member
Thread Starter
Join Date: Jan 2002
Location: Sydney, Australia
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
series3 dash go into a series1?
My dash isn't in great shape, so i thought i might upgrade it with a newer dash instead of getting the same one.
Can i put a series 3 dash in a series 1? are there any problems?
Can i put a series 3 dash in a series 1? are there any problems?
#5
Driving RX7's since 1979
iTrader: (43)
Join Date: Aug 2001
Location: So Cal where the OC/LA/SB counties meet
Posts: 6,096
Likes: 0
Received 8 Likes
on
8 Posts
I'll bet $5......
it will bolt right in. The interesting part will be integrating the parts that complment it.... the Heater/AC Logicon......, the plumbing for dash vents......, etc.
#7
Driven a turbo FB lately?
iTrader: (1)
Originally posted by dcamcoTII
Bump--anyone done this?? Gauge cluster and all
Bump--anyone done this?? Gauge cluster and all
I dont see it being too bad as long as you change everything, like i said before the major thing will be the wiring difference the sub harness and all the cluster wiring is totally different
Trending Topics
#8
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,841
Received 2,605 Likes
on
1,848 Posts
i've seen a few in junk yards, i think you are going to need everything (the wiring, heater, ac blower etc) but it should bolt right in
mike
mike
#9
ACBron Motorsport
Re: series3 dash go into a series1?
Originally posted by Besok
My dash isn't in great shape, so i thought i might upgrade it with a newer dash instead of getting the same one.
Can i put a series 3 dash in a series 1? are there any problems?
My dash isn't in great shape, so i thought i might upgrade it with a newer dash instead of getting the same one.
Can i put a series 3 dash in a series 1? are there any problems?
This is the inside of my Aussie series 3.
And this is the dash in my old series 2.
#10
Apprentice Guru
Join Date: Oct 2001
Location: Cloud Nine and Peak of God
Posts: 1,425
Likes: 0
Received 0 Likes
on
0 Posts
For export righthand drive series 3 [Aus, NZ. UK }, there was no diffeence in the dash compared with a series 2.
Replacing a series 1 with a series 3 rhd is relatively simple, primarily minor rewiring.
Replacing a series 1 with a series 3 rhd is relatively simple, primarily minor rewiring.
#14
ACBron Motorsport
There just pre made pods i got from the local parts & accesoories store here....
I normally make my own but i got lazy.
there not hard to make yourself, but these have the trimming vacumm molded.
Theres a book called "high performance car stereo", I think its by SA books??? its from the states so you gyus should have no worries finding it....
Its a bit old ( as in old theory's) but it is a great book and will tell you how to make your own pods and boxes the correct and easy way.
I normally make my own but i got lazy.
there not hard to make yourself, but these have the trimming vacumm molded.
Theres a book called "high performance car stereo", I think its by SA books??? its from the states so you gyus should have no worries finding it....
Its a bit old ( as in old theory's) but it is a great book and will tell you how to make your own pods and boxes the correct and easy way.
Thread
Thread Starter
Forum
Replies
Last Post