1st Generation Specific (1979-1985) 1979-1985 Discussion including performance modifications and technical support sections

running out of fuel..

Thread Tools
 
Search this Thread
 
Old 02-03-08, 03:29 PM
  #1  
domokun!

Thread Starter
iTrader: (2)
 
FBsliderseven's Avatar
 
Join Date: Jan 2007
Location: hawaii
Posts: 1,063
Likes: 0
Received 0 Likes on 0 Posts
Unhappy running out of fuel..

ok so today i decided to go for a nice 4th gear pull, but after around 4.5k my car starting bogging down and had absolutely no power at all. i just recently put in the carb base gasket, it runs better but once the secondaries kicks in there is just about no power.
i have a holley carb and a holley red fuel pump.
any ideas on what the problem is guys?
thanks.
Old 02-03-08, 05:52 PM
  #2  
Lives on the Forum

iTrader: (13)
 
Rx-7Doctor's Avatar
 
Join Date: Jul 2004
Location: Oregon
Posts: 10,584
Likes: 0
Received 11 Likes on 10 Posts
Standard question. When did you last service the fuel filter?
Old 02-03-08, 06:11 PM
  #3  
domokun!

Thread Starter
iTrader: (2)
 
FBsliderseven's Avatar
 
Join Date: Jan 2007
Location: hawaii
Posts: 1,063
Likes: 0
Received 0 Likes on 0 Posts
ive done that around 2 months ago.
i have a feeling that it might be the floats.
but i have no idea on how to adjust those.
Old 02-03-08, 06:54 PM
  #4  
Rotary Enthusiast
iTrader: (5)
 
kutukutu1's Avatar
 
Join Date: Jan 2008
Location: Southfield, MI
Posts: 1,296
Received 60 Likes on 38 Posts
The floats are easy to adjust, just take off the top cover of the carburator where the floats are located. Flip that over and let the floats hang, Get a ruler and measure the float from the gasket to the front of the float and it should be 16mm, then flip it over again and let it hang down, measure from the gasket to the farthers most point of the float and it should be 51mm give or take 2mm. If the floats are not right then you adjust them by taking the float out and bending the tab were the needle goes up or down according to how you have to adjust it and measure again until you get it right.
Old 02-03-08, 09:42 PM
  #5  
Registered Loser

 
2fast2rotar's Avatar
 
Join Date: Nov 2007
Location: Concord, NC
Posts: 206
Likes: 0
Received 0 Likes on 0 Posts
mine is having the same problem....with the same setup(minus the pump) I think it is just timing bec its spuddering in the low RPM range too... is yours??

I know its not my fuel filter b/c I removed it and placed it directly infront of the carb to keep a good eye on it. I did this b/c there is nasty **** in my tank b/c the car sat 4 a year.
Old 02-04-08, 01:51 AM
  #6  
domokun!

Thread Starter
iTrader: (2)
 
FBsliderseven's Avatar
 
Join Date: Jan 2007
Location: hawaii
Posts: 1,063
Likes: 0
Received 0 Likes on 0 Posts
2fast4rotar - you need a better pump, the stock one isnt enough for a holley.

mine runs smooth in 1st and 2nd gear redline. but as i hit redline in 3rd gear it seems to running out of fuel, im guessing fuel starvation?
anyone know anything about these holley carbs?
Old 02-04-08, 01:55 AM
  #7  
Rota-lution
 
Experiment.Seven's Avatar
 
Join Date: Feb 2008
Location: Reno, NV
Posts: 229
Likes: 0
Received 0 Likes on 0 Posts
Mine is experiencing the EXACT same thing. Replacing fuel filter tomorrow.
Old 02-04-08, 02:29 AM
  #8  
domokun!

Thread Starter
iTrader: (2)
 
FBsliderseven's Avatar
 
Join Date: Jan 2007
Location: hawaii
Posts: 1,063
Likes: 0
Received 0 Likes on 0 Posts
hmm...
maybe i should look at my fuel filter again....
does it matter if i mounted the fuel pump horizontally?
Old 02-04-08, 02:34 AM
  #9  
Rota-lution
 
Experiment.Seven's Avatar
 
Join Date: Feb 2008
Location: Reno, NV
Posts: 229
Likes: 0
Received 0 Likes on 0 Posts
I have no clue as to how to mount the fuel pump.

I know i will be running two filters though from here on out.

Have you used any type of seafom like products recently. I used Seafoam in my tank and i believe that's why mine is clogged.
Old 02-04-08, 07:06 AM
  #10  
Senior Member

iTrader: (3)
 
1stgenNutt's Avatar
 
Join Date: Dec 2006
Location: flatrock Alabama
Posts: 386
Likes: 0
Received 0 Likes on 0 Posts
Check fuel lines , fuel filter and tank for dirt or rust . I experienced the same thing
and i realized that we returned the carb lines. On a Holley you don't return the carb for return at all just cap the fuel return . make sure you are getting 7 lbs of fuel pressure . also, Holley's floats adjust from the top brass nuts on the bowls adjust the floats so that they weep just a Little from the sight holes . where they put the omp lines into the carb.
Old 02-04-08, 08:01 AM
  #11  
My 7 is my girlfriend.

iTrader: (5)
 
orion84gsl's Avatar
 
Join Date: Feb 2006
Location: London, Ontario, Canada
Posts: 3,162
Likes: 0
Received 1 Like on 1 Post
Originally Posted by 2fast2rotar
I know its not my fuel filter b/c I removed it and placed it directly infront of the carb to keep a good eye on it. I did this b/c there is nasty **** in my tank b/c the car sat 4 a year.
You still have to have a filter BEFORE the fuel pump. Your problem could very well be that all that nasty ****, is now clogging your pump, because you removed the filter. The filter wasn't put there arbitrarily, it's in that location for a reason.
Old 02-04-08, 12:09 PM
  #12  
Junior Member

 
ndmrpwr's Avatar
 
Join Date: Feb 2003
Location: Idaho Falls Idaho
Posts: 43
Likes: 0
Received 0 Likes on 0 Posts
google is our friend :-) http://www.holley.com/data/TechServi...Carburetor.pdf
Old 02-04-08, 07:33 PM
  #13  
domokun!

Thread Starter
iTrader: (2)
 
FBsliderseven's Avatar
 
Join Date: Jan 2007
Location: hawaii
Posts: 1,063
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by ndmrpwr
i just found that, but thanks anyway.
i dont think its the floats anymore.
it seems like the fuel is just cutting off completely.
Old 02-04-08, 09:17 PM
  #14  
Registered Loser

 
2fast2rotar's Avatar
 
Join Date: Nov 2007
Location: Concord, NC
Posts: 206
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by orion84gsl
You still have to have a filter BEFORE the fuel pump. Your problem could very well be that all that nasty ****, is now clogging your pump, because you removed the filter. The filter wasn't put there arbitrarily, it's in that location for a reason.
ever since I first checked the filter, it was after the pump. The pump shouldnt affect it at all.
Old 02-04-08, 09:34 PM
  #15  
Registered Loser

 
2fast2rotar's Avatar
 
Join Date: Nov 2007
Location: Concord, NC
Posts: 206
Likes: 0
Received 0 Likes on 0 Posts
What I don't understand is this.....

When you buy the RB setup they say "you have to have the high-power- fuel pump."

But when I baught my system I just used the stock pump and opened the jets a little(the flat-head screws on the front and back of the carb)

The car runs great when you mash the gas. It will chirp 1st, 2nd, and 3rd gears

but when I'm cruising at 60mph in 4th gear at 4200RPM it is wide open.

Also this only happens sometimes. Plus I cannot get the car to stop spuddering in the low RPM range, but when the secondaries in the holley open up it runs GREAT!!! is it worse the colder the car is.

... Sorry about taking over the tread, but I need the same answers as you man...

Am I shooting myself in the foot by not buying the high power fuel pump??
Old 02-04-08, 10:12 PM
  #16  
Thunder from downunder

iTrader: (1)
 
aussiesmg's Avatar
 
Join Date: Mar 2001
Location: Convoy, Ohio, USA
Posts: 3,843
Likes: 0
Received 1 Like on 1 Post
Sounds like filter, check it again you may have rust in the tank. Multiple filters wont stop the first one clogging up.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
C. Ludwig
Single Turbo RX-7's
49
01-30-19 06:31 AM
Rotospectre
New Member RX-7 Technical
3
03-28-18 03:33 PM
turbo-minivan
General Rotary Tech Support
69
02-04-16 12:29 AM
The Shaolin
2nd Generation Specific (1986-1992)
9
09-14-15 07:50 PM



Quick Reply: running out of fuel..



All times are GMT -5. The time now is 02:02 PM.