1st Generation Specific (1979-1985) 1979-1985 Discussion including performance modifications and technical support sections

Restricting fuel to the carb!? Car woes.. PLZ HELP

Old Dec 3, 2002 | 11:45 AM
  #1  
bcty's Avatar
Thread Starter
Boost This!
Tenured Member 20 Years
 
Joined: Nov 2001
Posts: 1,935
Likes: 0
From: Nanaimo, B.C, Canada
Restricting fuel to the carb!? Car woes.. PLZ HELP

Just picked up my 79.. new motor, still gaining compression.. but it will not start.. its keeps flooding like crazy.. tryed jumping, tryed roll start.. that almost got it but still no.. is there any way i can restrict flow to the carb? cn i pinch the fuel line before it goes into the carb? plz help me soon! thanks

Tyler

Last edited by bcty; Dec 3, 2002 at 11:47 AM.
Reply
Old Dec 3, 2002 | 11:53 AM
  #2  
rotor vs. piston's Avatar
Function > Form
Tenured Member 15 Years
 
Joined: Nov 2002
Posts: 10,890
Likes: 3
From: Catonsville MD (baltimore suburb)
Go find a fuel pressure regulator, until you fix your carb. It seems like your gaskets might be shot.
Reply
Old Dec 3, 2002 | 12:00 PM
  #3  
bcty's Avatar
Thread Starter
Boost This!
Tenured Member 20 Years
 
Joined: Nov 2001
Posts: 1,935
Likes: 0
From: Nanaimo, B.C, Canada
engine is perfect.. i will try and pull the bottom plugs and crank for a few seconds.. clean the plugs and see what i can do.. just found out that clamping the fuel line will empty the float bowls.. soo we will see.. ill keep ya posted! thanks
Reply
Old Dec 3, 2002 | 12:33 PM
  #4  
specRX7_22's Avatar
Rotary Enthusiast
Tenured Member 05 Years
 
Joined: Nov 2002
Posts: 1,013
Likes: 0
From: Eastern PA
just pick up a fuel pressure regulator. mine is holley brand. however these seem to crap out after a while due to the low fuel pressure these motors need. so check the pressure every once in a while because by crap out, i mean that it could could lean out the motor.

--eric
Reply
Old Dec 4, 2002 | 03:07 AM
  #5  
bcty's Avatar
Thread Starter
Boost This!
Tenured Member 20 Years
 
Joined: Nov 2001
Posts: 1,935
Likes: 0
From: Nanaimo, B.C, Canada
ok the motor was "gas washed" the whole exhaust was full of gas and leaking out the muffler.. i hope that the fuel regulator will help a bit... isnt there one we can buy that will work with our carbs a bit better? around 3-4psi actually? do u think the stock pump would cause this at all too? or maybe a new upgrade would be better?
Reply
Old Dec 4, 2002 | 03:27 AM
  #6  
nimrodTT's Avatar
all aboard!
Tenured Member 20 Years
 
Joined: Mar 2001
Posts: 1,204
Likes: 1
From: Houston
Originally posted by bcty
ok the motor was "gas washed" the whole exhaust was full of gas and leaking out the muffler
One of my carbs does this every once in a while - I could never figure it out and it doesn't happen regularly. Both carbs are regulated at 4.5psi. but only one exhaust tube drips gas on the ground (flux-core migs don't make good exhaust seams). More than just a float bowl full of gas ends up wasted so I'd like to know what is happening.
Reply
Old Dec 4, 2002 | 03:35 AM
  #7  
genrex's Avatar
Senior Member
Tenured Member 10 Years
 
Joined: Mar 2001
Posts: 520
Likes: 0
From: -
I think you have misdiagnosed the problem, bcty.

But whatever. The engine is new, and still under warrantee, right? Why mess with the warrantee and screw yourself?? - call the shop that built the engine, and calmly tell them what happens when you turn the key. I'd say you need to do what they tell you to do, since it's their warrantee that applies here!

This is business, and you need to cover your ***, eh.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
bb6guy
Old School and Other Rotary
10
Oct 1, 2018 08:07 AM
alphawolff
1st Generation Specific (1979-1985)
17
Nov 17, 2015 05:57 PM
bb6guy
3rd Generation Specific (1993-2002)
3
Aug 12, 2015 03:29 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 05:24 AM.