seanrot

iTrader: (2)

Well. I started the day trying to get the choke thermal swith to control my fan. That was a bust, thermal switch is broke. Then I spent an hour taking a old *** generic alarm system outa my car and fixing all the wires the last owners assed up with the alarm. Got my driver side door switch to turn the dome light on again. Bypassed the fuel pump relay while I was removing the alarm, since I was down there. Thought I accomplished alot for one day. Then I got bored at about 10 pm and went out and took the header and the rest of the exhaust off. mounted the turbo and fiddled around abit.
I figured I better install the turbo before I showed another pic of it. Starting to feel like the purple car

now without futher interuptions








I only have everything else to do. I figure if I had a full week I could finish it. But at this rate should take a month or two.

Comments and questions are welcome...

Rotor13B

Can you turn that carb hat around? If so, turn it around and reposition the intake on it 180 and install a front mount intercooler on it. Eh, on second look at that 4th picture it appears the fuel inlet might not let you do that. Maybe it's just the angle of the picture, i don't know. Looks nice, keep up the good work.

luiml73

iTrader: (1)

Congrats!! Looking good

What is the reason of the box(Plenum). I was having a discussion today with a friend that is doing the same setup with a dellorto. But he's just going to make a Y pipe

like this, but Not EFI


I think I read somewhere, that this is not recommended for street cars.

What is the difference?

seanrot

iTrader: (2)

To do 180 with the carb hat I have to get a whole new intake manifold and linkage. BTW I already have a front mount intercooler to mount, with the hat in that position.

seanrot

iTrader: (2)

Ya got me as for difference or the pro's and con's, but the reason im going with it is cause it was cheap and came with the kit.

RX7145

iTrader: (1)

Is that a Fram oil filter I see?

Directfreak

iTrader: (2)

That's a pretty cool looking kit, didn't you get it in Japan for like $120 bucks?

If that was you... You Bastard!

seanrot

iTrader: (2)

<----- yea old dirty bastard guilty as charged...

mwatson184

Lets see a price breakdown for your turbo setup. Mine is going to be cheap, but not nearly as cheap as yours.

Rutnick

great looking setup. What are the specs for the car?

seanrot

iTrader: (2)

My car should almost have a ebay banner on it

Car 250.00
Turbo, exhaust manifold, intake manifold, intercooler, and piping 138.00
fuel pressure regulator 105.00 after shipping
Weber 48 IDA carb 250.00 jets and orther little stuff for the car 120.00
GSL-SE fuel pump 65.00
GSL-SE oil cooler 40.00 piping 45.00
Racing beat oil block 35.00
muffler 40.00
2.5" mandrel bends 60.00
small silencer 15.00
2.5" 7 foot exhaust pipe 10.0

About 1200.00 so far + 150.00 or so for stuff i forgot

also Im doing all the work myself, from the welding exhaust to the putting air in the tires.

Specs for car please see signature

V8kilr

Although it doesnt look like it at first glance, I have a hunch thats a pretty nice looking engine bay when all cleaned up.

82streetracer

iTrader: (1)

as far as plenums vs just a intake pipe.

Carbs require a plenum, and efi does not.

you could put a plenum on a EFI system like in the pic, but I wouldnt do any good.

A plenum coverts flow into pressure of something like that.

Mr BiG G

sweet setup dude

seanrot

iTrader: (2)

Ill never know never plan on cleaning it... just joking..

The car is actually really damn ugly. 250.00 overheating gsl. little rust on the rear fender, but the last owner had macco do a green over the red paint about 10 years ago I would guess by the condition of the paint job. If I actually took the time to clean the engine bay, I think it would look decent. not iotus standards but ok.

at least when I race someone I wont be embarrased to loose, at least till the hoods are popped..

d0 Luck

finally someone w/ a 48 ida blowthrough.. much props for you my friend... someday, i'll get there also.. lol

that's the jdm 12a sigma turbo hat, correct?

seanrot

iTrader: (2)

Thanks, and yes to the JDM sigma hat question..

Also Update... had a little time on my hands today. Made the downpipe and started the first section with a pre-silencer..



Home made downpipe less forty dollars...

Chance to brag about it ......priceless.

That will be my last tasteless joke on the subject..

Dammit got my foot in the damn picture

web777

I think your friend's set up will work better. Most people have boxy plenums because they are easy to build and with forced induction it is less critival 'cause everything is pressurized.

seanrot

iTrader: (2)

Another decent day of getting stuff done.. Finished the downpipe said that earlier, but I put it on thats a good thing. Also started putting on the intercooler. Fits very nicely can even keep the a/c if I decide to put the compressor back on

Shot of the downpipe.

Shot of intercooler from above.

the lower inlet of the intercooler and the hole I cut to put the pipes though. Please forgive the ugly pipes they will be stripped and painted after they are mocked up.

Shot from under the bumper. last owner did the wiring on the black plastic piece. So busy fixing other stuff, didnt even notice till I saw the picture. One more thing on the clean up list.

Directfreak

iTrader: (2)

Damn, at this pace, you'll be done in a week!!

That thing is gonna fly!

web777

Good job! Your IC pipe routing is similar to mine. I would use the lower piping from the turbo and higher one to the plenum. Also, are you going to running a filter in that turbo?

Here's how I did mine.

seanrot

iTrader: (2)

I wish, Just about to hit the big slow down. Gotta go back to work on Saturday, taking the family to the zoo tomorrow. Then the one that really hurts waiting for parts. My original plan for the oil retun is shot so I have to get more fittings.

Do have a couple questions hopefully some one can help with.

How much can I boost. Stockport engine. I'm thinking about 8lbs but with the intercooler I should be able to get away with a little more.

Anyone care to estimate the power output???????

seanrot

iTrader: (2)

Thanks,

I thought about doing my piping that way but i figured the cooler would more efficient with a short pipe to plenum and the long one from the turbo. I probably wont make a difference but it was the thought that made me do it that way.

I tried to find a filter for it. but the inlet to the turbo is only two inches. I need to find an adapter or something. for right now it will have that screen over it.

EDIT:
Actually I just had a thought for the filter. Ill take that HKS filiment tthat you have in yours cut it so it fits nicely over my little screen on clamp it down

Directfreak

iTrader: (2)

10 psi, low (or no) lag, and 200-225 to the wheels.

seanrot

iTrader: (2)

Thanks,

and for lack of better words

I have just the guage to keep track of that .68 bar