1st Gen General Discussion The place for non-technical discussion about 1st Gen RX-7s or if there's no better place for your topic

Fan Clutch

Thread Tools
 
Search this Thread
 
Old Apr 20, 2022 | 01:49 PM
  #1  
Jax85fb's Avatar
Thread Starter
Junior Member
 
Joined: Apr 2022
Posts: 20
Likes: 0
From: MA
MA Fan Clutch

Hello, I'm a newbie, so please excuse me if I'm not on target with the questions. I have 1985 GS FB, which I have had for a couple of months and just getting it on the road.
I believe I need a new fan clutch and cant seem to be able to locate one. I also will need a new belt. If anyone can point me in the right direction, I would be forever grateful.
Suggestions welcomed! Thx, Jackson

PS tried Ebay, Rock Auto, Parts Geek with zero luck.
Reply
Old Apr 20, 2022 | 04:24 PM
  #2  
KansasCityREPU's Avatar
Out In the Barn
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (9)
 
Joined: Mar 2005
Posts: 6,704
Likes: 1,250
From: KC
I did a Google search and found this new one.

https://www.atkinsrotary.com/store/C...9-15-210B.html

I have a couple of spares. $125 + shipping.

New clutch fans are hard to find. You can check out Facebook or place a wanted-to-by on this site in the MarketPlace here: https://www.rx7club.com/market/

How did you determine the old one was bad?

Last edited by KansasCityREPU; Apr 20, 2022 at 04:31 PM.
Reply
Old Apr 20, 2022 | 04:29 PM
  #3  
Jax85fb's Avatar
Thread Starter
Junior Member
 
Joined: Apr 2022
Posts: 20
Likes: 0
From: MA
Fan clutch

I can stop the fan with my finger. I just ordered a new belt. I noticed it had a tear in it.
Reply
Old Apr 20, 2022 | 05:37 PM
  #4  
Maxwedge's Avatar
Slowly getting there...
Tenured Member: 5 Years
Liked
Loved
Community Favorite
iTrader: (1)
 
Joined: Jun 2018
Posts: 1,638
Likes: 359
From: SE PA
I think you "should" be able to stop the fan with your finger. Also it depends on the temp of the air flowing over it. The hotter the radiator the more it "locks up" but never fully locks up. That's the beauty of a fan clutch... even at full engagement it will slip a little if you gun the throttle. It isn't "directly" mounted to the rotating assembly like the non-clutch fans from the 50's/60/70's.

I got my replacement clutch from Mazdabestpartsonline.com for $231.73 plus shipping ($242.57 total). This was the best price I could find on the web last year.

If you googoo "'85 RX-7 Cooling Fan Clutch" you get lots of $100 hits, but the folks here say they never fit right. Buy genuine Mazda for this part. And yes, it's redicuously expensive compared to a Chevy or furd fan-clutch from the same time. Welcome to RX-7's.
Reply
Old Apr 21, 2022 | 03:09 PM
  #5  
Jax85fb's Avatar
Thread Starter
Junior Member
 
Joined: Apr 2022
Posts: 20
Likes: 0
From: MA
thanks, I'm going to install the new belt and see how that goes.
There's a lot to learn. The previous owner installed a Weber Carb and I think it's drawing too much gas. I'm going to play with that next.
fun times!
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
pdxgen1
1st Generation Specific (1979-1985)
6
Oct 27, 2020 11:38 PM
rx7_FREAKKK
NW RX-7 Forum
29
Mar 18, 2012 12:02 PM
GlennC
1st Generation Specific (1979-1985)
23
Dec 1, 2004 11:13 AM
jeremy
1st Generation Specific (1979-1985)
4
May 10, 2002 02:24 AM




All times are GMT -5. The time now is 04:36 PM.