rotormind

Just wanted to start a thread on what kind of times and trap speeds you guys are running in the 1/4 mile. Thought it should be interested and it hasn't been done in the na forum yet so I figured I might as well do it.

Pedro Racing

3/4 chassi, datsun 1200 1971 13B PP tII transm 9.96et 1/4 mile, now wants 9.35et will see.

RotaryPicha

iTrader: (2)

Pedro ^^

blown7

'84 GSL-SE, stock chassis, 4.44 rear gears, 13B-PP, weber 48IDA, 13.3@100

1BADSP

iTrader: (4)

street driven 78 RX-3SP,13b Peripheral Port,t2 trans,stock rear end with 4:88's,24.5 in slicks.best time with that set up was 12.7@110mph.

rotormind

Ok, it's awesome to see that the PP guys are posting there times but it's not a competion so if some of u guys ran a 15 or more it's very understandable. We all know how hard it is to run a good time on these na's so if everyone can post their times it can be a lot more interesting.

ultimatejay

iTrader: (1)

73 RX2 sedan with 12abridgeport, stock chassis, stock suspension, 8.5" tire and stock TII trans. 12.07 running out of fuel on the top end. Will be in the 11's very, very soon. Vid is in my sig

Rxmfn7

iTrader: (4)

Ive been wanting a thread like this for a long time If any of you guys know your cars weight, can you please post it also? Thanks!

n0ferz

iTrader: (4)

Ok here we go

79 toyota starlet 12a stockport, 4.88 rear gears, stock carb, crappy exhaust , 13 inch tires - 15.6seg 1/4mile

Jimbo II

79 rx7, 13b Extend port, 48ida, s2 LSD, 14.6@108 with **** launch. Old owner has done high 13's.

ArmyOfOne

iTrader: (12)

'84 Rx7, 6 port BP, Holley 600, GSL LSD 4.10 13.14@105 weight 2150.

Working on something much better right now.

rotormind

Has anyone got in the 14's with an FC?

flaco

iTrader: (7)

14.2 streetported s4 on an mt4 microtech

rotormind

please, more details on this one.

aerosev

1978 s1 rx7 12a mild extend port, standard carb re-jetted, exhaust system, electronic ignition, lightened flywheel, stock wheels/tyres, series 2 LSD, series 3 gearbox

14.565 @ 92.4mph

running float bowls out of fuel after half way point

Pedro Racing

1/2 chassi, webber, ford 6.20

peejay

These threads keep popping up and then never get updated.

I don't drag race, I just see it as really cheap dyno time, but the numbers are in the signature.

Hyper4mance2k

iTrader: (40)

14.6@89mph
old 83GSL with a stock GSL-SE 13b and 45dcoe carb with rb exhaust and basic upgrades. 140whp
https://www.rx7club.com/1st-gen-general-discussion-207/%2A%2A%2A-1st-gen-1-4-mile-leader-board-%2A%2A%2A-652168/

S1sevenNZ

FC 12.6

http://www.youtube.com/watch?v=rjIZeiOrwXc

drag 7

85 rx7 10.50 at 126 13b p-port gene berg 58mm on pump gas g-force trans gm 12bolt dif

rotormind

Im shooting for 200rwhp with my fc. My motor just got built with an aggressive street and exhaust port. I have a racingbeat uncollected exhaust, i dont know how this exhaust performs but im gonna give it a shot. At the moment im looking for a standalone and from there i will have to figure the rest out. I know its not impossible but its not gonna be easy. Any advice is welcome.

fidelity101

iTrader: (11)

dying old atkins SP 6pt
stock 14"s
stock old whomped out suspension
1st gen trans
4.10 LSD
Racing beat street exhaust
full interior
1st time drag racing

[youtube]http://www.youtube.com/watch?v=7hN5XoCaW34[/youtube]

15.3 @89.95 mph

you cant really hear me over the civic

dbragg

iTrader: (7)

82 base, 12a stock port, RE 48 IDF, RE exhaust, RB light flywheel and clutch, had been sitting in the woods for 10+ years 2 months before, old crappy tires, and timing 180* off which caused some spark knocking at the end of the 1/4.

15.3 @ 93mph

vosko

iTrader: (4)

probably 7 years ago now ? i ran 15.9 @ 86mph. stock reman motor S5 n/a with intake and headers and bonez cat

it was really hard to get below 16's!

89RedsunGTUs

iTrader: (1)

i've got a 16.1 with a SP, Headers, Rtek (untuned) kinda dissappointed was hoping for 15.7's