Haltech E8 coil setup.
#2
E8 Using Stock Ignition System:
Wiring:
Ignition Output 1 (light green) to Leading Coils (Pink)
Ignition Output 2 (white/black) to Trailing Coils (Pink)
Ignition Output 3 (green/black) to Ignition Toggle (white)
Software Setup:
Spark Type – Distributor
Charge Time – 4.5ms
Spark Edge – Falling
E8 Using Aftermarket Ignition Coils with Wasted spark:
Wiring:
Ignition Output 1 (light green) to Leading Coils (both leading coils)
Ignition Output 2 not used
Ignition Output 3 (blue) to Trailing 1 Ignition Coil (front rotor)
Ignition Output 4 (blue/yellow) to Trailing 2 Ignition Coil (rear rotor)
Software Setup:
Spark Type – Direct Fire
Charge Time – 4.5ms (dependant on ignition coils used)
Spark Edge – Falling (dependant on ignition module used)
E8 Using Aftermarket Ignition Coils with Direct Fire:
Wiring:
Ignition Output 1 (light green) to Leading 1 Ignition Coil (front rotor)
Ignition Output 2 (white/black) to Leading 2 Ignition Coil (rear rotor)
Ignition Output 3 (blue) to Trailing 1 Ignition Coil (front rotor)
Ignition Output 4 (blue/yellow) to Trailing 2 Ignition Coil (rear rotor)
Software Setup:
Spark Type – Direct Fire
Charge Time – 4.5ms (dependant on ignition coils used)
Spark Edge – Falling (dependant on ignition module used)
Wiring:
Ignition Output 1 (light green) to Leading Coils (Pink)
Ignition Output 2 (white/black) to Trailing Coils (Pink)
Ignition Output 3 (green/black) to Ignition Toggle (white)
Software Setup:
Spark Type – Distributor
Charge Time – 4.5ms
Spark Edge – Falling
E8 Using Aftermarket Ignition Coils with Wasted spark:
Wiring:
Ignition Output 1 (light green) to Leading Coils (both leading coils)
Ignition Output 2 not used
Ignition Output 3 (blue) to Trailing 1 Ignition Coil (front rotor)
Ignition Output 4 (blue/yellow) to Trailing 2 Ignition Coil (rear rotor)
Software Setup:
Spark Type – Direct Fire
Charge Time – 4.5ms (dependant on ignition coils used)
Spark Edge – Falling (dependant on ignition module used)
E8 Using Aftermarket Ignition Coils with Direct Fire:
Wiring:
Ignition Output 1 (light green) to Leading 1 Ignition Coil (front rotor)
Ignition Output 2 (white/black) to Leading 2 Ignition Coil (rear rotor)
Ignition Output 3 (blue) to Trailing 1 Ignition Coil (front rotor)
Ignition Output 4 (blue/yellow) to Trailing 2 Ignition Coil (rear rotor)
Software Setup:
Spark Type – Direct Fire
Charge Time – 4.5ms (dependant on ignition coils used)
Spark Edge – Falling (dependant on ignition module used)
#3
multipersonality disorder
Join Date: Feb 2002
Location: so. cal
Posts: 5,656
Likes: 0
Received 0 Likes
on
0 Posts
^ i poked around for hours and hours until i realised that was like the second to last page in the manual.
if i can't learn the hard way, i just won't learn at all
if i can't learn the hard way, i just won't learn at all
Thread
Thread Starter
Forum
Replies
Last Post
eplusz
General Rotary Tech Support
15
10-07-15 04:04 PM
rotor_veux
2nd Generation Specific (1986-1992)
3
09-28-15 09:25 PM
killerrx710
Adaptronic Engine Mgmt - AUS
5
09-28-15 09:13 AM
killerrx710
2nd Generation Specific (1986-1992)
1
09-24-15 10:57 PM