better watch out rat, im working on a setup to make 500+ to the wheels on pump/AI. :)

I think I just found my new engine builder. All you need now is a sticker that says "I wanna go fast"

http://tobetheman.com/wp-content/upl.../wall1_sml.jpg

11.1 so far..

Bring it homie! I got a new turbo setup in the works that should get me to 600...

what are you goin with a TEEEIGHTYEIGHT? t91
OOH how bout one of those IhI TPL9lB

I am secretly trying to touch tha big 500 (but dont tell anybody)

the pt67 should do it :)

What kind of 60 foot time?

Andrew

It seems like the numbers were made with the boost spike/creep, rather then boosting to a straight psi and holding it till redline...of course the numbers look good with the spike, then bleeding down to the 20 lbs or so at redline. To force it to hold the boost, a stiffer wastegate spring is needed, and once you do that and it still bleeds boost down, then you know your turbo is out of breath. I had a 61.5mm compressor wheel, and we tried running it to 30 lb with a 22 lbs wastegate spring, but it just kept bleeding down to 27 lbs.
Also, why does it seem so laggy and the full boost powerband too short? I made 27 lbs boost at 4500 rpms and it held that boost all the way to redline...about a 4K fullboost powerband. See how flat the torque curve is, which is what you want, and hp lines are...and the boost is rock solid . smoothing of 0

561hp w/ a 61.5mm turbo? d a y u u u m haha

damn...600 on stock ports and stock exhaust. :wink:

[/QUOTE]
Quote:
Originally Posted by J-Rat
Bring it homie! I got a new turbo setup in the works that should get me to 600...




hes not on stock ports no mo

- Jarrett

Wow, on stock ports!!! :rlaugh:

plz read entire thread. kthnx.

stock tranny,rear end,axles?

awesome numbers man

Do you think you've gotten all the car can do with the 490 whp? I've always been a big advocate of using all the current hp before trying to make more. Thats why...I'll be sticking with a stretch goal of 425 whp this summer and then this fall/winter make the push for more. 11.1 though is stinking fast so maybe you have..

Na.... I am about positive he runs 4 x 1600's on one walbro awiht an E11 from what i saw.... and that not enough injector and pump to be running methanol at those power levels

I plan to run E85 with HP goals of around 600.... But on an REW motor and gt42

I think crispeeds car was a t76 with either a q or s trim exhaust....

Jrat what is up your sleeve for a turbo?? at least a 70mm inducer? :)

Will be a 67mm inducer. Not sure I really care to push for 600 anymore. 550 should be fine.

:)

i swapped the 57 trim to the pt67 for about a month, then found the cheap gt42 so went for it.......

all i know is that the 67 will get you there..... my car was unbelieveably faster on the 67 vs the 57 on same boost levels, never went more than 14psi on a rough street tune and it had to be at about 430ish wheel, not even tapping the potential of that compressor....... wonder alot if i am foolish for not pushing the 67 and instead going with maybe a lag monster 75mm 42

and the 57 pushed my car to 11's on 14psi

will you run a larger hotside than a P-trim?

anyway you're still the man.......... anyone who pushes a 61.5 compressor to near 500hp knows how to make the most of a turbo :)

I wish I could take credit, but that goes to Ryan(Moremazda), Glen Weaver (AZRotaryRockets), and Trevor, the tuner extraordinaire. Without them I would have never made it.

Gratz J-Rat on those numbers. got a question though, what do you have for a driveline? stock trans and driveshaft? or have you upgraded?

Its all stock driveline except for an upgraded clutch...:)