t 78/stock motor ? how long will it last
how long will my engien last.with 48k/78k not to sure miles and a t 78 at 15 psi . should i not run it hard and just rebuild it .what if the engien gose boom will i cause damage to the turbo . should i run lower boost .or should i put my t78 turbo on my scooter
Nobody can tell you that. It depends on the condition of the engine,the tuning,the use of that turbo,what other peripherals will you put to support that turbo etc etc.
If the engine is in good condition and the rest are made up correctly then you should have no problems, although i would start saving money for a rebuild
And yes, if the engine goes boom there is a chance to cause damage to the turbo. Although thats very rare but depends on what brakes inside the engine some metallic particles may reach your turbo throu the exhaust port and cause damage on the turbo.
If the engine is in good condition and the rest are made up correctly then you should have no problems, although i would start saving money for a rebuild

And yes, if the engine goes boom there is a chance to cause damage to the turbo. Although thats very rare but depends on what brakes inside the engine some metallic particles may reach your turbo throu the exhaust port and cause damage on the turbo.
I'll be running 10lbs until I can save enough $$ for a rebuild. My car currently has 47k miles on it. And stock motor. If you have a good rotating assembly, its usually quite a bit cheaper to get it rebuilt. But if you're going to go down the re-man path, then I'd keep the boost cranked up until it let go!! CJ
front mount ,koyo,hks timing,1600cc2nd,850cc prim,power fc,mid pipe,apex boost controler
kaza rear,chang gearing, rebuilt trans,short shifter
power plant,sway bars,strutbars,engein brace,
renforced radiator mounts/swaybar
shift light,boost gauge,water temp,fule presure,egt,oil temp,oil presure,
this is what i have on my car know . i dont want to have to rebuil unless i have to . i know that it dependon tuning ,the way you drive how much you boost and iknow. nobby can answer this .but if i get some feed back it may give me a idea or a guesstamation on time of explosion
thanks
kaza rear,chang gearing, rebuilt trans,short shifter
power plant,sway bars,strutbars,engein brace,
renforced radiator mounts/swaybar
shift light,boost gauge,water temp,fule presure,egt,oil temp,oil presure,
this is what i have on my car know . i dont want to have to rebuil unless i have to . i know that it dependon tuning ,the way you drive how much you boost and iknow. nobby can answer this .but if i get some feed back it may give me a idea or a guesstamation on time of explosion
thanks
Trending Topics
Nobody can tell any numbers especially with a rotary engine. Even if the car is stock you cannot tell numbers. You may pop the engine at 1K miles or 100K miles.
But if you do everything correct and you take care of it should last for another 30-50K.
But if you do everything correct and you take care of it should last for another 30-50K.
how much $ would be good for a reman. with and with out port work. well what i am getting out of this . is that if i get a reman. the same thing could happen. 1 mile or 80k miles. it all depends on the tuner. know when i do reman. what are the thing that i want in the reman. what should i make sure i get.
Tony,
Its all in the tuning. Make sure it is tuned well and the motor should last a while. You can get a reman for $2k from Malloy Mazda, but dont worry about that until yours blows up
Jason
Its all in the tuning. Make sure it is tuned well and the motor should last a while. You can get a reman for $2k from Malloy Mazda, but dont worry about that until yours blows up

Jason
Did I put A map on the Power FC? If so the timing should be good, you would need to adjust the A/F. You can do it either on the street or dyno. On the dyno you can adjust the timing but I think you just want a safe tune and not trying to go for as much HP.
Jason
Jason
it was the fule pump . when you take out the stock one . cut the metal tube half way up . then put on 3/8 hose to the fule pump and the metal tube . it was bleeding off . i have some things too fix but soo far its ok




CJ