Enough Fuel???!!!
10-27-04, 09:34 AM
#1
Junior Member
Thread Starter
Join Date: Oct 2004
Location: ILLINOIS
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Enough Fuel???!!!
Have been working on a 93 rx7 for awhile now, just wondering if the setup I am using will require more fueling.. Specs:
Atkins Street Port- Dowel Pinned Motor less than 5 Miles on it
Greddy Single Turbo Kit using a Garrett a/r60
Greddy Downpipe w/ external Wastegate
Apexi Cat Back
Underdrive Pullies
M2 Chip
Greddy Front Mount Intercooler/piping
Running 8-9 Psi on 93 octane
Stock Fuel system as far as I know
Should I upgrade the fuel system to run those low boost levels or leave it alone if I dont plan on raising the boost levels anytime soon??
Atkins Street Port- Dowel Pinned Motor less than 5 Miles on it
Greddy Single Turbo Kit using a Garrett a/r60
Greddy Downpipe w/ external Wastegate
Apexi Cat Back
Underdrive Pullies
M2 Chip
Greddy Front Mount Intercooler/piping
Running 8-9 Psi on 93 octane
Stock Fuel system as far as I know
Should I upgrade the fuel system to run those low boost levels or leave it alone if I dont plan on raising the boost levels anytime soon??
10-27-04, 09:48 AM
#3
Rotary Enthusiast
Join Date: Feb 2001
Location: In the Sky
Posts: 1,190
Likes: 0
Received 0 Likes
on
0 Posts
based on what you listed and not sure on some parts you have .. i highly recommed talking to a experienced shop/tuner to better guide in the right direction.. ported single turbo kit cara dont go well with a static M2 chipped ecu and stock fuel injectors.. your results will turn into a soon to be blown engine..
Originally Posted by yelog60
Have been working on a 93 rx7 for awhile now, just wondering if the setup I am using will require more fueling.. Specs:
Atkins Street Port- Dowel Pinned Motor less than 5 Miles on it
Greddy Single Turbo Kit using a Garrett a/r60
Greddy Downpipe w/ external Wastegate
Apexi Cat Back
Underdrive Pullies
M2 Chip
Greddy Front Mount Intercooler/piping
Running 8-9 Psi on 93 octane
Stock Fuel system as far as I know
Should I upgrade the fuel system to run those low boost levels or leave it alone if I dont plan on raising the boost levels anytime soon??
Atkins Street Port- Dowel Pinned Motor less than 5 Miles on it
Greddy Single Turbo Kit using a Garrett a/r60
Greddy Downpipe w/ external Wastegate
Apexi Cat Back
Underdrive Pullies
M2 Chip
Greddy Front Mount Intercooler/piping
Running 8-9 Psi on 93 octane
Stock Fuel system as far as I know
Should I upgrade the fuel system to run those low boost levels or leave it alone if I dont plan on raising the boost levels anytime soon??
10-27-04, 10:06 AM
#5
Junior Member
Thread Starter
Join Date: Oct 2004
Location: ILLINOIS
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
No plans to go any higher than 10psi as of right now, maybe next summer up it to 15 with the right upgrades... I believe the kit is the td06, got the kit w/ the car and no paper work..Hp numbers are not a concern at this point, just want to get it on the street and put a few miles on it...
10-27-04, 02:32 PM
#7
Rotary Enthusiast
Join Date: Feb 2001
Location: In the Sky
Posts: 1,190
Likes: 0
Received 0 Likes
on
0 Posts
try searching as this has been covered numerous times.. personally i like the 850cc/1600cc with a Microtech LTX8S but again theres other choices out there!
get a set-up your tuner is familiar with
good luck
get a set-up your tuner is familiar with
good luck
Originally Posted by yelog60
What fuel pump/injectors would you guys recommend??
Also what ecu setup is the best for my application?
Also what ecu setup is the best for my application?
Thread
Thread Starter
Forum
Replies
Last Post
rgordon1979
3rd Generation Specific (1993-2002)
40
03-15-22 12:04 PM