Mounting additional injectors in the intercooler pipe - how far from throttle body?
#1
Junior Member
Thread Starter
Join Date: Jun 2003
Location: Wales, UK
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Mounting additional injectors in the intercooler pipe - how far from throttle body?
As above.
I'm trying to mount two additional injectors on the intercooler piping. However, i'm a bit worried about mounting them so far from the throttle body. They can't be mounted in the plastic elbow and the red bit is a samco hose so they can't be mounted there either.
This just leaves the small section of pipe between the red silicon hose and the light on the right (of the picture)
Is this too far away from the throttle body and likely to cause droplet formation? If so, is it worth getting the GReddy elbow and then have another section of piping made up?
I'm trying to mount two additional injectors on the intercooler piping. However, i'm a bit worried about mounting them so far from the throttle body. They can't be mounted in the plastic elbow and the red bit is a samco hose so they can't be mounted there either.
This just leaves the small section of pipe between the red silicon hose and the light on the right (of the picture)
Is this too far away from the throttle body and likely to cause droplet formation? If so, is it worth getting the GReddy elbow and then have another section of piping made up?
#2
Stay tuned...
iTrader: (3)
Join Date: Jul 1997
Location: West Islip, Long Island NY
Posts: 2,917
Likes: 0
Received 1 Like
on
1 Post
Originally Posted by Welsh Dan
As above.
I'm trying to mount two additional injectors on the intercooler piping. However, i'm a bit worried about mounting them so far from the throttle body. They can't be mounted in the plastic elbow and the red bit is a samco hose so they can't be mounted there either.
This just leaves the small section of pipe between the red silicon hose and the light on the right (of the picture)
Is this too far away from the throttle body and likely to cause droplet formation? If so, is it worth getting the GReddy elbow and then have another section of piping made up?
I'm trying to mount two additional injectors on the intercooler piping. However, i'm a bit worried about mounting them so far from the throttle body. They can't be mounted in the plastic elbow and the red bit is a samco hose so they can't be mounted there either.
This just leaves the small section of pipe between the red silicon hose and the light on the right (of the picture)
Is this too far away from the throttle body and likely to cause droplet formation? If so, is it worth getting the GReddy elbow and then have another section of piping made up?
Anthony
#3
Junior Member
Thread Starter
Join Date: Jun 2003
Location: Wales, UK
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Do they really? I was under the impression that they only sold it with one boss? I know that HKS did one with two in, but that replaces the whole elbow and costs about $700.
#6
Banned. I got OWNED!!!
Join Date: Jul 2004
Location: next to the polishing wheel!!!
Posts: 1,179
Likes: 0
Received 1 Like
on
1 Post
The older Greddy elbow had two injector holes.I cut one off and put a blow off valve there. The other I use for the air temp senser,mounted in nylon .The best place for more injectors is on the motor side of the throttle body ,not the innercooler side . Maybe weld injector bungs on the out side curve of the sec ports of the UIM .How many cc of gas do you need that you can not go with bigger units in the four stock bungs?
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
CaptainKRM
2nd Generation Specific (1986-1992)
14
08-26-15 09:52 PM