3rd Gen Jeremy

Ok so this is officially 1 kill and 2 losses but it's a cool video.

http://dsmvideo.vidiac.com/video/52a...19001eb12f.htm

The evo kept beating me off the line but I was reeling him back in, just ran out of room. Happened every time but he did have the advantage of AWD and a 2-step. Plus I'm not much of a drag racer so I had to get used to launching the car. I got better in the later races but the evo was my first 2 races.

The STi beat me out of the hole but then I spanked him twice.

The Civic is a strange beast, it's got drag slicks up front and little tiny tires on the rear, like a reverse funny car. It's got a big single too. However, he kept shutting down before the end of the run so technically I won but if he wasn't having breakup, he would have smoked me. I'm still sequential twins.

Gotta fix my wheel hop and put some better tires on the car and I can compete with these guys.


Hope you enjoy,
Jeremy

BoostedFd3s

iTrader: (3)

that was a nice little vid...

work on launching your car and you should be able to keep up, even beat that evo.

efranklin

hmmm you should try uploading to streetfire.. cant seem to watch it.. what are your mods though?

3rd Gen Jeremy

It's open to the public. You should try it again. It's not my video so I didn't put it there. It's actually the guy in the Evo that made the video.

matty

whats done to the cars...good quality vids by the way.

3rd Gen Jeremy

I can only speak for these cars:

STi: stock

EVo: Intake, Exhaust, Cam, 2-step, tires

FD: This is gonna be a long list

CB, MP, DP
Efini Twins
Efini Y-Pipe
PFS Med IC and duct
HKS SSQV
Greddy Elbow
Emissions Elim
Hose Techniques Hose Job
New Solenoids
KG Parts Fuel Rail Kit (SS Lines, 1600 sec, 850 primary, FPR)
Walbro FP
GReddy Turbo Timer and PRofec B Spec II,
Apexi PFC tuned by Steve Kan
FLudiyne Radiator
Pettit AST
K&N intakes and hard pipe
Pettit Heat Shield
WT, OT, NB AFR gauges
Pettit Boost Gauge
Greddy Pulleys
HKS Twin Power

Ready to be installed:
Koni Yellows,
Pettit Launch Kit (Trailing arms, diff bushings and A-arm bushings) (this should help my launches - was getting a lot of wheel hop)
Eibach springs,
dual oil coolers

Can't vouch for the F-bodies

Solstice: Stock - not GXP

Denali - Not stock at all

Civic:
Stripped street racer
Big Single Turbo,
Tuned,
Cams
Drag Slicks Up Front
Drag skinnys in back
lots of lightening mods
I'm sure other things like clutch and gears but I don't know for a fact.

3rd Gen Jeremy

That's it exactly. I'm faster than he is but he's me off the line. I've got Fuzion rears on stock rims and some bad wheel hop. I've really gotta figure that out. I've got the Pettit kit that I've still got to install. Probably need to install some driver mods too.

I'll let you guys know what happens next.

BoostedFd3s

iTrader: (3)

dang...that's a nice little list of mods you got...well get your pettit launch kit installed and hopefully it'll help you out...btw how much and where did you purchase this pettie launch kit from?? pettit??

3rd Gen Jeremy

Got it from a guy on the forum, think I paid like 120 for it and the heat shield. Not sure though.

matty

how much u boosting?

3rd Gen Jeremy

15 psi sequential

matty

wow...u should be pissing on those cars.

3rd Gen Jeremy

Those are some fast cars and I'm getting pretty bad wheel hop. I'm not getting off the line very well at all. That plus my tach is all over the place so I'm doing a lot of guessing as to where I should shift. I really need to get a new one.

Don't underestimate the evo or the power of a big single turbo. That evo has been tuned by the owner and he's a pretty smart guy. He's a programmer like me. That 2 step is pretty neat too. It holds the revs at exactly where he wants to launch until he lets off the clutch then the thing just grips and goes. My car is still hopping around like it's the damn Easter Bunny delivering eggs.

ArmenMAxx

iTrader: (21)

i too would like to know why our cars wheel hop so much. Ive got R1 shocks and Tein springs and good kumo v700 tires and every time i drop the clutch i think my car is gonna fall apart because of the hop

what does the pettit lauch kit do

3rd Gen Jeremy

It will fall apart because of the hop. You've gotta get out of the gas when that happens. Every time I floor it in 1st or second gear, the back end starts hopping on my launches.

The kit replaces the diff busings and upper a-arm busings with no-compliance polyurethane bushings. It also replaces the trailing arms with new arms that have no-compliance joints. It should fix my problem but if it doesn't completely, I'll have to get a diff brace. I'll keep you guys updated.

Stix37867

iTrader: (1)

Well as a easy and cheaper fix for the tach is too get a G-tech. I have the road race version but it also comes with the drag setup too. It displays a tach on it in drag race mode that reads the electrical signal from the cigarette lighter. Pretty cool actually. I have a similar problem after i start my car for about 5 minutes. Not quite as bad as yours but similar.

3rd Gen Jeremy

Yeah the evo had one of those. It's pretty cool too.

Have you checked it against the real rpm from the ECU? How accurate is it?

ArmenMAxx

iTrader: (21)

is the kit made for launching/dragging, or does it make the car handle better also? Because im gonna track ounce ina while

Stix37867

iTrader: (1)

Yeah i actually made sure it was accurate. I haven't tested the horsepower type functions yet but the rpm works perfectly. I used my PFC commander to verify both the tach and the gtech before setting the gtech and it came out perfect. It actually reads to the tenths (i.e. 2510).

3rd Gen Jeremy

My car is set up for auto-X and this kit only stiffens up the differential and the rear-end. You'll still be able to track the car.

3rd Gen Jeremy

That blows my mind that it can read rpm that accurately through the cigarette lighter. How the hell can they do that? It's amazing anyway, I looked up their site and it's supposedly for real.

Stix37867

iTrader: (1)

It has to do with the electrical pulses that the alternator makes. That's why when setting it, it has you rev to 2 different rpms so it can learn and calculate the curve of pulses per rpm. The horsepower is supposed to be really accurate as long as you get an accurate weight reading of your car. I love it and it looks sweet too.

2FAST7S

neat little gizmo...I always thought they were more of a "guess"! I gotta go play with one now.

Oh, quick note on the wheel hop...how 'bout you just lower your tire pressure a bit say to about 24 psi or so. As your Evo buddy, hold your rpm at about 4k. Slip the clutch a bit and ease into the gas, QUICK!!!lol that should allow you to stay within 2 cars and let you catch up and pass him...free launch kit!

3rd Gen Jeremy

Yeah, I checked my pressure and I was at 40 psi. No wonder huh!

I was launching at 3500 and getting massive wheel hop. I've got a lot of power, just gotta get better at putting it down. You could smell my clutch burning from me slipping the clutch too, it was pretty overpowering. I got much better as the day went on and I should have given him another run but I'll have to wait till next time.

I probably need to put a 6-puck in as well as the launch kit and get some drag radials if I'm gonna be playing in this league. Some of these guys are really fast!!

Drag racing is really big down here. I"m not so much into it but some of these guys are.

3rd Gen Jeremy

By the way, he's launching at 6500 rpm