Rotary Starlet
#1
Junior Member
Thread Starter
Join Date: Feb 2007
Location: modesto, ca
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Rotary Starlet
I have a 83 starlet that i want to swap a rotary into. I picked up a 12a with a weber sidedraft on it. I would really like to turbo it. I am a vw bug guy so i have lots of experience blowing thru carbs. Is it even worth it on the 12a? how much boost will they take? What do u guys do about the timing do u just lock it out? The car will mostly be used for a driver and autocross. Would a 60 trim t3 with a .48 hot side be too small?And would th first gen tranny be ok or should i get a secnd gen? I also noticed that there seems to be some kind of oiler that feeds the intake mani, how does this react to boost? Sorry for all of the Q's but i want do get this swap rollin the stock 50 horse just aint cuttin it. I'm hoping for 150 out of the rotary
Thanks
Jeff
Thanks
Jeff
#2
blown up motors
iTrader: (1)
the 12a takes to boost very well... your best bet is the 1st gen section and or searching for 12at or 12a turbo... the max is like 21 psi for a stock 12a altho it wont last much longer then a week you can do a niec 10psi and be well over your 150hp... ez set up would be
12a stock ports, gslse oil pump, high psi oil reg, FMOC, 2nd gen turbo & manifold, then an adaptor 13b to 12a, blow thru carb, carb hat, FMIC,IC piping,turbo II tranny good clutch, boost controler,BOV, mod the 2nd gen waste gate, boost gauge... i think that about sums it up
12a stock ports, gslse oil pump, high psi oil reg, FMOC, 2nd gen turbo & manifold, then an adaptor 13b to 12a, blow thru carb, carb hat, FMIC,IC piping,turbo II tranny good clutch, boost controler,BOV, mod the 2nd gen waste gate, boost gauge... i think that about sums it up
#3
blown up motors
iTrader: (1)
or you could buy this https://www.rx7club.com/showthread.php?t=627646 it just went for sale and im sure it will goo pretty quick.........but if you want a 12at its everything you need for under 1200.....well every tihng but a wide band o2
#4
Junior Member
Thread Starter
Join Date: Feb 2007
Location: modesto, ca
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the replies. I searched and read alot. I have plenty of turbo stuff to make it happen and i can make anything i need so im not worried about that. The question i still havent been able to find the answer to is the ignotion timing. In the vw world i just weld the distributor and lock the timing at 24 but i dont think thats going to apply here. I also noticed that with the weber the vacum advance pods were not in use. Whats the proper way to do this?
#5
blown up motors
iTrader: (1)
you do pretty much the same thing welding the distributor to full advance and running the vacum advance.... im about 95% sure this is the right way. as for timming im not sure what to tell you to run it at guess that depends on your fule and the boost you are going to be running
i will ask my friend that ran a 12at set up for a long time and i will get back to you
cheers PaTricK
i will ask my friend that ran a 12at set up for a long time and i will get back to you
cheers PaTricK
#7
Junior Member
Thread Starter
Join Date: Feb 2007
Location: modesto, ca
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Thanks!!!
Im picking up a trans today. The motor i have came out of an auto 85. what flywheel do i need? does it have to be the same year?
Thanks again
Jeff
Im picking up a trans today. The motor i have came out of an auto 85. what flywheel do i need? does it have to be the same year?
Thanks again
Jeff
Trending Topics
#9
Junior Member
Thread Starter
Join Date: Feb 2007
Location: modesto, ca
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
No its a second gen n/a trans. I got the trans driveshaft and clutch for a hundred bucks so i couldn't pass it up. Im close now to having all the stuff i need.
#11
Junior Member
Thread Starter
Join Date: Feb 2007
Location: modesto, ca
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Are they all interchangeable? A friend told me that i needed to get one from the same year as the engine so it wouldn't affect the balance. Is that true?
#12
Soft & Wooly
Join Date: Jan 2007
Location: Lakewood, CO (formerly Seattle)
Posts: 291
Likes: 0
Received 0 Likes
on
0 Posts
It doesn't have to be exactly the same year but it needs to be from the right group. I think for 12A it is 74-82 and 83-85. But I could be wrong. Best is to get an aftermarket flywheel to match the transmission, with a counterweight to match the engine, since the flywheel on the 12A (215mm) won't match the 13B clutch (225mm). I think I have this all right. It might be that the 12A in 83+ had the big flywheel and not just a different counterwight. If I'm wrong I'm sure someone will correct me...
The 81+ NA transmissions are stronger than the old ones and should hold up except at the drag strip - 1980 and older are actually pretty weak and will probably break. Stronger yet are the RX-4, REPU, FD and Turbo II transmissions. Those are pretty tough.
The 81+ NA transmissions are stronger than the old ones and should hold up except at the drag strip - 1980 and older are actually pretty weak and will probably break. Stronger yet are the RX-4, REPU, FD and Turbo II transmissions. Those are pretty tough.
Thread
Thread Starter
Forum
Replies
Last Post
datfast1
Old School and Other Rotary
18
06-20-19 10:53 PM
Under PSI
3rd Generation Specific (1993-2002)
19
09-23-15 11:47 PM