86 7 VIBRATION plese help !
#2
Blah, Blah, blah
iTrader: (13)
Join Date: Feb 2001
Location: Tacoma, WA
Posts: 307
Likes: 0
Received 0 Likes
on
0 Posts
Umm ok I'd check your engine/clutch/transmission. W/O any more info it's pretty useless to say your car just vibrates. Location of vibration? can you pull the throttle cable from the engine bay to try and narrow it down for us?
#5
STEP ASIDE !!!!!!!
Thread Starter
iTrader: (19)
Join Date: Feb 2009
Location: Salem,OR
Posts: 1,270
Likes: 0
Received 0 Likes
on
0 Posts
idk i just had a new clutch put in 2 months ago///// . 2 hrs ago i put a jack under front of trans , lifted about quarter inch . motor ran smooth. now what ?????
Trending Topics
#8
Blah, Blah, blah
iTrader: (13)
Join Date: Feb 2001
Location: Tacoma, WA
Posts: 307
Likes: 0
Received 0 Likes
on
0 Posts
Well if all you did was jack the tranny up that will also move the motor. So w/o seeing anything I'd say one or more of the three mounts is bad or you have some loose bolts you tension with the lift.
This is all assuming that the tranny and engine are solidly mounted together. Really nothing else is affected just by moving the engine/trans up and down, at idle anyway.
This is all assuming that the tranny and engine are solidly mounted together. Really nothing else is affected just by moving the engine/trans up and down, at idle anyway.
#10
Senior Member
Join Date: Nov 2005
Location: united states
Posts: 541
Likes: 0
Received 0 Likes
on
0 Posts
diff mounts go out. you would feel that more so when your shifting, is it only 2000 rpms? also 2000 rpms in nuetral.. 1st, 2nd, all gears? has it only starte happening since the new clutch was installed. theres 2 mounts for the engine one under the spark plugs on the drivers side the other under the exhaust, the transmission has 2 mount that connect to a crossmember that has a bushing in the center. i have seen the bushing go bad. i think a mount would make more of a vibration or shutter when shifting in gears heavy load situation. But if the hestition goes away when lifting the transmission i would guess mounts also make sure all the bolts are connecting the engine and trans. If you have the ebrake tight and try and hold the brake and let off the clutch in 1st gear you should be able to load the engine and drivetrain and hopefully notice if a mount is moving more then it should. good luck.
#11
STEP ASIDE !!!!!!!
Thread Starter
iTrader: (19)
Join Date: Feb 2009
Location: Salem,OR
Posts: 1,270
Likes: 0
Received 0 Likes
on
0 Posts
the vibration is from 2000 and up. i checked the mount bolts . tight. i ll take it to the guy that did clutch and have him look at it . i have spair tranny mount on parts car. i ll let u no, thanks alot . :} 10mm / aprechiate it alot !!@!!
#12
Rotary Enthusiast
iTrader: (26)
The clutch work that was done...
Was the pressure plate replaced?
Was the throw-out bearing replaced?
Was the pilot/needle bearing replaced?
#13
STEP ASIDE !!!!!!!
Thread Starter
iTrader: (19)
Join Date: Feb 2009
Location: Salem,OR
Posts: 1,270
Likes: 0
Received 0 Likes
on
0 Posts
its main tranny mount . i took off and the center bushing came apart . i need mine back bob / lol/ can any 1 ship me 1 . pay pal. ??? salem ore thank s alot for the help . the guy that did the clutch should of saw that ; yes it did it before. 10mm
Thread
Thread Starter
Forum
Replies
Last Post