Help - Did I buy the right turbo? (New member)
#1
Junior Member
Thread Starter
Help - Did I buy the right turbo? (New member)
Hi guys,
I had an impulse buy and splashed out on a new turbo, it was on clearance at the local store and picked it up for a great price, from my limited (and to be honest slightly rushed) research it seemed to be suitable but wanted to check with you guys on what you thought.
I realize likely all the information I need is somewhere here on the forumn but thought it would be easier to get some up-front feedback from you guys.
Here is my current setup:
13b Full Bridgeport
big injectors
Microtech LT-10s
Flowed s4 Turbo (9 psi)
Turbosmart Ultragate 38mm External gate
Big intercooler
Power: 280HP@wheels freshly dyno tuned
I just splashed out on a turbo at the local dealer (was at a clearance $$rate) and did do some research prior however I would like to check if I got the right one for me and if it will work fine for my application.
I am able to return it if its not "perfect" but moreover I want to make sure its suitable for a rotary engine and can do the job.
What I am wanting:
good spool up 3-4k rpm, good/more power, street friendly
Here is what I purchased:
Borg Warner s300sx - Model: #177281
Compressor
Wheel inducer 66mm
Compressor outlet 3.00
Compressor inlet 4.00
Turbine
Exducer 73mmTurbine outlet 4.00 V-band
Housing T4 open flow .88 A/R
AND...Turbosmart Pro-gate lite 50mm v-band Wastegate (with 14 psi spring)I will be having it dyno tuned again immediately after of course.
Look forward to hear your feed back, did I waste my time? should I take it back? should it do the job?
Thanks
I had an impulse buy and splashed out on a new turbo, it was on clearance at the local store and picked it up for a great price, from my limited (and to be honest slightly rushed) research it seemed to be suitable but wanted to check with you guys on what you thought.
I realize likely all the information I need is somewhere here on the forumn but thought it would be easier to get some up-front feedback from you guys.
Here is my current setup:
13b Full Bridgeport
big injectors
Microtech LT-10s
Flowed s4 Turbo (9 psi)
Turbosmart Ultragate 38mm External gate
Big intercooler
Power: 280HP@wheels freshly dyno tuned
I just splashed out on a turbo at the local dealer (was at a clearance $$rate) and did do some research prior however I would like to check if I got the right one for me and if it will work fine for my application.
I am able to return it if its not "perfect" but moreover I want to make sure its suitable for a rotary engine and can do the job.
What I am wanting:
good spool up 3-4k rpm, good/more power, street friendly
Here is what I purchased:
Borg Warner s300sx - Model: #177281
Compressor
Wheel inducer 66mm
Compressor outlet 3.00
Compressor inlet 4.00
Turbine
Exducer 73mmTurbine outlet 4.00 V-band
Housing T4 open flow .88 A/R
AND...Turbosmart Pro-gate lite 50mm v-band Wastegate (with 14 psi spring)I will be having it dyno tuned again immediately after of course.
Look forward to hear your feed back, did I waste my time? should I take it back? should it do the job?
Thanks
#3
.88 ar is fine for a 3-4K rpm spool range. However you'll be looking to be on full boost in the 4K rpm range, if it's a twin scroll hotside with matching manifold it'll aid in getting there a bit faster.
being bridgeported I wouldn't think going smaller would be of benefit.....just be a mismatch of parts.
being bridgeported I wouldn't think going smaller would be of benefit.....just be a mismatch of parts.
#4
Borg's .88 t4 housing is undivided. Most of my limited turbo knowledge is based on the diesel performance world, but am I wrong to think that the .91 divided housing with a matching manifold would be a better option?
#5