All those women, but I know one he won't have....

 

Thats how I roll!
Ernie dont worry man,Theres to many to worry about than just 1 all day.

 

I will have the flyers ready by the end of next week.If anyone can help me out I will send you some to give out just pm me your address.
Thanks Guys

 

T shirt decision time.Well after not getting a return email from our guys that make the rx7club tshirts and last years bbq t-shirts I have decided to make and get them again myself this year.In my opinion lasts years looked like it took 5 minutes of work on a 3 dollar t-shirt that lasted all of 2 washes.
I used the some of the design from a few years ago but they will be digital printed.(More detail) and on a nice shirt also like a a few years ago. T-shirts will run around 13.60 each to make.
Here is the design for this year.

They will be for sale at the show for 15.00
Of course volunteers that help me out get one free.

 

Roy,

Once the Dulle Towne Center Meets start up I'll grab a bunch of flyer from you and hand them out. I'll pm you my address.

Victor

 

Needs a car or two on the shirt like the flier ;p

 

Hopefully i will have both my 10th ae and my fd running and take them both up there. Hey Roy if you need any help let me know you are right down the street. And where is you red t2? And jsplit you never got in touch with me to get that door can't afford it now since i am dishin out like $6000 to have the engine rebuilt but turns out i need a reman deal kinda deal.

 

The tII is right around the corner at my friends House.He use to be a mechanic at ELD and he has everything in the world to work on the car.
The damn subframe on the car is ****.I got alot of work to do on that bitch.Hoping for June 1st to have it all done.I have dropped 6k in parts and for a motor so hopefully it will turn out nice.Thats not even including the body and paint I still have to get done and pay for.

 

Hmmm Like a certain red fd with a playboy model on it

 

$6000? where are you having that done?

 

Yeah I'm thinking that would be damn sexy!

 

Anything is good as long as Jon doesn't tie it up around his stomach and look like a sweetie!

 

Who in the world is charging you $6k for a motor?!!!

 

I got a 88 10th parts car if you need a sub frame i just took the diff out to sell it.
And jsplit i am having GoodfellaFD3S rebuild it but need a reman($2400) because the engine was the orginal with 126,000 and the iron failed before the coolant seal but still started up and ran fine with alot of smoke. I also need a wiring harness($715), turbos($300), vaccum hoses($?), installed(around $1250), and all the gaskets and lines ect($1000) ect(thats not everything, injectors and a bunch of stuff i am forgeting) trust me it adds up quick not exactly $6000 but guessed around that amount to make myself feel better when the bill comes but i bought the engine and wiring harness since i get a really good deal at mazda. Everything was brittle and breaking stupid twins i need to go single. This car needed alot of work but got a good deal on it and already have the mods for some decent power(pfc, 1300's, exhaust, and intake. Still need a intercooler and fuel pump soon but plan to make a trip up to pfs to get a good tune once my 2000miles are up. I would have done it myself it i knew i was going to have to get a reman but he stands by his work and trust him with my car.

 

I have no comment - I'll just have you notice Ernie's big blue comment and well yeah.

What gaskets and lines etc are $1000? And are your turbo's and injectors really shot? Did you call Ray @ PFS? would be more local and I'd venture to guess cheaper and with a warranty.

 

I will not be doing that again - was a one time deal - well that or unless someone else pays me to do it again when I've been drinking heavily

 

***** out racing sweatshirt 15.00
case of beer by 10am 18.99
Getting your drunk *** friend to wear the shirt like a little drunk bitch PRICELESS!!

 

I got bigger secondarys and my rear turbine housing came off(no comment) so it was pretty much gone. I had to get all new oil metering lines, fpd, coolant hoses, belts, fuel lines, o2 sensor bung in my mid pipe for my wide band, turbo gaskets, intake gaskets, motor mount, pliot bearing, and the list keeps on going. I didnt talk to pfs because i always tried to call and they were always busy and there prices were pretty high for a rebuild but his work is good. I thought is was going to be cheaper but this car like i said needed alot more work than i expected since it wasnt well taken car for basically almost 130,000 and the only thing that was replaced was an oil filter. I am saying $6000 including all work not just for a engine it will cover everything i am having done to the car and replacing. It is a big estimate i rather have more money than i need that not enough. But i am going to have my car tuned at PFS and know i am going to have to go through a bunch of crap since the engine work was not done there. Enough about me spending money its making me sad. And more about this BBQ and these ladies and cars dont forget the cars. And stop distracting me from my work i have essay that is due tomorrow that i am working on last minute because i am a slacker.

 

^ perhaps becasue its late or something but im finding it really hard to read your posts......

remember...the enter button is your friend

 

Pehaps it was late since you read it at 12:01 And guys this is for my fd not my 2nd gen if you didnt know. And got some more parts to add to the list for another $100 spark plug wires and a harness. It just adds up quick just ask GoodfellaFD3S how bad my car was if you dont believe me.

 

Yo Big E

We are . Ihor and I have already compared pricing with all the other major (reputable) shops on the east coast, and we're very competitive with regards to labor pricing. As far as parts prices (wiring harness, fpd, gaskets etc) we're all stuck paying exhorbitant mazda prices unfortunately.....Mr. Crowe is the best deal around

Edit: like Matt mentioned, his engine bay is basically original everything, with like 125k miles on it. Everything consumable needs replacement, and everything not consumable needs scrubbing in the parts washer because it's all FILTHY.....he had oil leaking from every possible spot, and a few others besides that

Edit again: this BBQ looks like a great time, I'm impressed by how organized you guys are

 

I wasn't aware of the rest of the things Rich. I was just under the impression it was a motor for $6k. All good..

 

Would you all believe I'll be there... in a rotary-powered RX7

Long story short, I'm getting divorced and had to sell EVERYTHING pretty much except the house - it's in my name now and I'm basically starting over. I picked up a 91 NA in excellent shape from a fellow member in North Carolina.

By the BBQ I should have my stereo installed, the windows tinted, the car lowered and possibly new wheels, but right now everything is clean and STOCK including a freshly rebuilt 13B.

What the heck is this world coming to???

 

Sorry to hear about the divorce Joey.I saw some pics of the car before,looks nice.
Glad to hear your going to make it to the bbq.

 

Look on the bright side Joey, there's a good chance you can hook up at the bbq....lol...