FREE Stuff in Rockville, Maryland
Thread Starter
Weird Cat Man
Joined: Aug 2001
Posts: 2,868
Likes: 3
From: A pale blue dot
FREE Stuff in Rockville, Maryland
I am moving to Seattle.... I have to do a cross-country move, and even though the movers are paid for by my company, I feel bad making them haul stuff that I probably just don't need any more.
This stuff is all free, but you MUST PICK UP BY WEDNESDAY!!!!!!!!!! NOT THIS WEEKEND, not next week... it goes in the Thursday morning trash pickup or maybe to the dump Wednesday night if nobody wants it.
1 - FD Power Steering Cooling Loop. This is the part that mounts in front of the radiator to cool P/S fluid
2 - FD A/C Parts. I have all the parts (somewhere) to put A/C back on an FD that had it ripped out by someone. If you come over, you can pick them up, but honestly it's up to YOU to have a little checklist to make sure you're getting the whole setup. The only part I can't give you is the evaporator, which is still installed in my car under the dash. They should be in good shape. (probably would wanna install fresh rubber seals)
3 - Rotor housings. I have two rotor housings, that I think go with an FD engine. I don't have time to go back downstairs and look for the FD vs. FC differences, so if you want them, I think they are from my original FD engine which had around 50k miles on it when it cracked/chipped some seals. I think one has a scratch on it from a seal and the other is lightly scraped up from a chipped seal. Even if you don't want to use them in an engine, you could use them for porting practice.
4 - FC Turbo end plates. One front plate with gear. Moderate scuffs/burn marks on the end plate, and the stationary gear has a mangled main bearing still in it. Not sure if you could lap this and re-use it or not (due to heat damage??) Also have one rear plate. Rear plate has moderate burns and scuffs on it. In addition it is NOT USABLE because I did some porting experiments on it and drilled a hole through the port wall intentionally heh. You could take it and practice porting or grinding if you like. Does not contain a gear, but I might be able to find the gear in the garage someplace. I also have no clue where the center plate is, but it's around somewhere.
5 - Eccentric shaft from something in the 13B lineup. Some scoring on the main bearing areas that you can feel with your finger. I have NO clue if you can smooth it down and use it with fresh bearings or not. Death was NOT due to over-rev so it should be straight. Threads on the rear end are slightly mashed due to me improperly removing a flywheel but are still there, and I think you could bolt a flywheel on it.
1320 Wild Oak Terrace
Rockville, MD 20852
If you wish to call "dibs" on something, REPLY to the thread. PM DOES NOT COUNT.
All parts will be gone by Wednesday night or thursday morning.
Brian
This stuff is all free, but you MUST PICK UP BY WEDNESDAY!!!!!!!!!! NOT THIS WEEKEND, not next week... it goes in the Thursday morning trash pickup or maybe to the dump Wednesday night if nobody wants it.
1 - FD Power Steering Cooling Loop. This is the part that mounts in front of the radiator to cool P/S fluid
2 - FD A/C Parts. I have all the parts (somewhere) to put A/C back on an FD that had it ripped out by someone. If you come over, you can pick them up, but honestly it's up to YOU to have a little checklist to make sure you're getting the whole setup. The only part I can't give you is the evaporator, which is still installed in my car under the dash. They should be in good shape. (probably would wanna install fresh rubber seals)
3 - Rotor housings. I have two rotor housings, that I think go with an FD engine. I don't have time to go back downstairs and look for the FD vs. FC differences, so if you want them, I think they are from my original FD engine which had around 50k miles on it when it cracked/chipped some seals. I think one has a scratch on it from a seal and the other is lightly scraped up from a chipped seal. Even if you don't want to use them in an engine, you could use them for porting practice.
4 - FC Turbo end plates. One front plate with gear. Moderate scuffs/burn marks on the end plate, and the stationary gear has a mangled main bearing still in it. Not sure if you could lap this and re-use it or not (due to heat damage??) Also have one rear plate. Rear plate has moderate burns and scuffs on it. In addition it is NOT USABLE because I did some porting experiments on it and drilled a hole through the port wall intentionally heh. You could take it and practice porting or grinding if you like. Does not contain a gear, but I might be able to find the gear in the garage someplace. I also have no clue where the center plate is, but it's around somewhere.
5 - Eccentric shaft from something in the 13B lineup. Some scoring on the main bearing areas that you can feel with your finger. I have NO clue if you can smooth it down and use it with fresh bearings or not. Death was NOT due to over-rev so it should be straight. Threads on the rear end are slightly mashed due to me improperly removing a flywheel but are still there, and I think you could bolt a flywheel on it.
1320 Wild Oak Terrace
Rockville, MD 20852
If you wish to call "dibs" on something, REPLY to the thread. PM DOES NOT COUNT.
All parts will be gone by Wednesday night or thursday morning.
Brian
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
