Microtech Area is for discussing Microtech systems

Microtech Need Fuel Map For Lt8 Please

Thread Tools
 
Search this Thread
 
Old Jun 16, 2005 | 10:49 PM
  #1  
CT44ST's Avatar
Thread Starter
Junior Member
Tenured Member 05 Years
 
Joined: Jan 2004
Posts: 7
Likes: 0
From: CALIFORNIA
Need Fuel Map For Lt8 Please

INSTALLED ON S4 WITH STOCK 550CC INJECTORS, I AM NOT ABLE TO TUNE IT TO DRIVE IT AROUND, I CAN ONLY GET IT TO STARTUP AND IDLE , BUT WONT ACCELERATE WELL, IT SOUNDS UNEVEN, WHEN YOU DRIVE FOWARD IT CUTS OFF AROUND 2500 RPM, IT STARTS MISFIRING, DOES ANYONE HAVE A FUEL MAP THEY CAN SHARE SO I CAN HAVE A STARTING POINT. THE AIRFUEL RATIO STAYS AROUND 15.00 BUT IF LOWERED THE MS ON THE INJECTORS TI GOES AS HIGH AS 18.00 BUT IF RAISED THE MS ON THE INJECTORS IT DOESNT DROP BELOW 14.7 ON A/F

IT IDLES
20"HG-1.90ms 15"HG 1.67MS
LOAD MAP IS BASIC FROM THE FACTORY, BUT I HAVE TRIED LOWER AND HIGHER NUMBERS WITH NO SUCCESS.
ANY FEED BACK WOULD BE HELPFUL, I HAVE CHECKED THAT BOTH PRIMARIES FIRE AND THAT THE 4 COILS FIRE AS WELL, ONE THING THE TRAIL PLUGS ALWAYS COME OUT WET , AND THE LEADING DRY. IF I LOWER THE IDLE FIGURES TO LEAN IT OUT, IT RUNS WORST
Reply
Old Jun 17, 2005 | 01:00 AM
  #2  
10sec rx7's Avatar
Rotary Enthusiast
Tenured Member 20 Years
 
Joined: Mar 2001
Posts: 1,353
Likes: 9
From: Sydney, Australia
something is not rite with your setup the stock map works perfectly with stock injectors,

check you tps is set correctly and the timing is set right
Reply
Old Jun 17, 2005 | 03:39 AM
  #3  
1sgen's Avatar
583 rwhp 1st gen
Tenured Member 15 Years
iTrader: (1)
 
Joined: Jul 2004
Posts: 397
Likes: 0
From: texas
sounds like the staging of the sec injectors , ihad similar problem and found that the sec injectors where frozen .
just a hint.
Reply
Old Jun 17, 2005 | 10:05 PM
  #4  
CT44ST's Avatar
Thread Starter
Junior Member
Tenured Member 05 Years
 
Joined: Jan 2004
Posts: 7
Likes: 0
From: CALIFORNIA
thank you for feedback, i have calibrated the tps, like the manual asks, i have to set at 00 when pedal is closed and then when i step on it, it goes up to 99, that is what the manual says, the timing i have check as well. but the map numbers from the factory has worked for you guys well. i mean the map from micro tech?
Reply
Old Jun 20, 2005 | 11:21 PM
  #5  
BOOSTED Vert
Tenured Member 10 Years
 
Joined: Sep 2002
Posts: 2,307
Likes: 0
From: Miami
check your rpmlim/rpmcut. See what those are set at. And also check the wiring for your injectors.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Skeese
Adaptronic Engine Mgmt - AUS
65
Mar 28, 2017 03:30 PM
stickmantijuana
Microtech
30
Apr 23, 2016 06:37 PM
sen2two
AEM EMS
9
Oct 23, 2015 07:51 PM
befarrer
Microtech
3
Aug 22, 2015 05:52 PM




All times are GMT -5. The time now is 04:54 AM.