Microtech Area is for discussing Microtech systems

Microtech Microtech lt10s starting issue

Thread Tools
 
Search this Thread
 
Old Aug 29, 2011 | 10:20 AM
  #1  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
Microtech lt10s starting issue

I have an S5 TII with 750cc secondaries, stock turbo, arc top mount and I have a microtech lt10s with the x4 ignition, my car gets right to where its about to start, but then just keps turning over. I currently have silverrotor's TII map in my car and I feel like im at a dead end, any ideas?
Reply
Old Aug 29, 2011 | 11:37 AM
  #2  
Sammy Built's Avatar
501 WHP Club
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (18)
 
Joined: Feb 2008
Posts: 521
Likes: 8
From: South Tampa
Upload some snap shots off your program. Have you recently rebuild or done a compression test?
Reply
Old Aug 29, 2011 | 12:26 PM
  #3  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
idk how to uplad photos, and compression is good according to pettit racing
Reply
Old Aug 29, 2011 | 12:27 PM
  #4  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
it was rebuilt before I got it**
Reply
Old Aug 29, 2011 | 12:59 PM
  #5  
Sammy Built's Avatar
501 WHP Club
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (18)
 
Joined: Feb 2008
Posts: 521
Likes: 8
From: South Tampa
Was the car running before with the program from silverrotor you said that you upgraded your secondaries but still should not cause it to not start. Make sure your map sensor is fitted correctly then check your calibration on your Tps if all is good pull your plug s out lmk what you see...
Reply
Old Aug 29, 2011 | 01:03 PM
  #6  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
I tried to calibrate the tps and I couldnt figure it out at all, I have to be explained to like a 5year old when it comes to electronics. hahaha
Reply
Old Aug 29, 2011 | 01:21 PM
  #7  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
I removed the leading and trailing plugs on the rear rotor and the leading was dry but the trailing was wet
Reply
Old Aug 29, 2011 | 01:47 PM
  #8  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
^^ same goes for the front rotor as well
Reply
Old Aug 29, 2011 | 02:16 PM
  #9  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
map sensor fitted correctly you mean the vacuume line going fromt the intake manifold to the microtech?
Reply
Old Aug 30, 2011 | 10:35 AM
  #10  
Sammy Built's Avatar
501 WHP Club
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (18)
 
Joined: Feb 2008
Posts: 521
Likes: 8
From: South Tampa
OK vacumn line is fitted so check. Trailing plugs wet so you definatelly getting fuel as leading that works as a wastespark so that's ok. Now for the tps that needs to be calibrated for the car to start on smoothly. So I'm going to pm your number and just text me and ill tell you exactly how to calibrate but you need a hand controller or laptop with a single.
Reply
Old Aug 30, 2011 | 10:37 AM
  #11  
Sammy Built's Avatar
501 WHP Club
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (18)
 
Joined: Feb 2008
Posts: 521
Likes: 8
From: South Tampa
I mean dongle
Reply
Old Aug 30, 2011 | 12:45 PM
  #12  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
alright sweet, thanks a lot! when we speak on the phone, there are a few updates on the car I want to make you aware of as well.
Reply
Old Aug 30, 2011 | 07:09 PM
  #13  
MazdaMan87's Avatar
Thread Starter
Junior Member
 
Joined: Aug 2011
Posts: 35
Likes: 0
From: Palm Bay FL
ok well idk what the hell I did, but it runs and starts just fine, its hard to get started but it starts, the real text will be tomorrow when the engine cools down.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
stickmantijuana
Microtech
30
Apr 23, 2016 06:37 PM
1993fd3sracer1
3rd Generation Specific (1993-2002)
29
Oct 13, 2015 01:57 PM
FB_Frank85
1st Generation Specific (1979-1985)
6
Aug 31, 2015 03:31 AM
befarrer
2nd Generation Specific (1986-1992)
4
Aug 14, 2015 04:18 PM




All times are GMT -5. The time now is 01:28 AM.