FD3S Rear "Euro" Washer/Fluid Tank
#203
That said - the manufacturer doesn't believe we should experience ANY yellowing - regardless of if it's behind a panel or exposed to sunlight.
#204
Don't worry be happy...
iTrader: (1)
Black isn't a bad idea. But I wanted something translucent. My thought was "it's good to be able to see how much fluid is in there" - but admittedly - we won't be able to see it behind the interior panel.
That said - the manufacturer doesn't believe we should experience ANY yellowing - regardless of if it's behind a panel or exposed to sunlight.
That said - the manufacturer doesn't believe we should experience ANY yellowing - regardless of if it's behind a panel or exposed to sunlight.
#206
Senior Member
iTrader: (7)
My comment about the yellowing is not purely aesthetic. If plastic is yellowing it's often times becoming brittle or weakening in general. I stand to be corrected on that though as I'm most familiar with plastics in the engine bay which obviously is exposed to heat as well as chemicals.
Someone with more understanding than I have, please feel free to correct me on this.
Nick
#207
Rotary Enthusiast
1. Spalato - 2 tanks
2. ZoomZoom - I'm in for at least 1. Maybe 2.
3. Slideways FD - 1
4. Silvertrd - 1 tank
5. jza80 - 1 tank
6. the spyder-
7. Izanami - 1 tank
8. SpeedCrazie - 1 Tank
9. photoresistor - 1 Tank
10. jsemerica - 1 Tank, maybe 2
11. Myocardial Infarction - 1 Tank
12. Rocketeerbandit - 1
13. Brekyrself - 2
14. 20005.3 - 1
15. Knotsonice - 1
16. Kensin - 1
17.Gio612
18.7krayziboi
19.#slevin
20. Fourtyounce - 2 maybe 3. Matt Gold for PreZident!
21. One for me please, Charlie
22. Redgti (James, uk) -1
23. Khan Racing - 1
24. Sigma
25. Alex Newman - 1 (UK)
26. thatdon
27. MattUK (UK - Can post to a mate state side if required)
28. Ptrhahn. 1
29. Iantboyd - 1
30. Fendamonky - 1
31. Sc0rp7 - 1
32. ColdFeet - 1
33. jkstill
34. Montego -1
35. Zepticon - 1 tank
36. Matthew Ng - 1
37. p51hellfire - 1
38. thanson90
39. s8nana - 1 (AU)
40. Runrex -
41. Garethb -1 (New Zealand)
42. Dhanson31
43. Ondabirdhouse - 1 (possibly 2)
44. Tictakman - 1
45. BaconHunter - 1
46. Trout2 - 1
47. spirit rx-7 - 1
48. Saham -1
49. Cvzg77r-1
50. pingu81 - 1
51. moshaka - 2 tanks maybe 3
52. Ryans93rx7 - 1
53. Rarotary - 1
54. TWIZTIDRX -1
55. XPT700 - 1 tank and shipping to Scotland
56. Sukisuki - 1
57. Daleclark - 1
58. Smokey The Talon - 1
59. Ghoujoumian - 1
60. Talkwrench (UK) - 1
61. red_dragon - 1
62. Street-heat7 - 1 maybe 2
63. Jonnybravo408- 1
64. THE TECH
65. KompressorLOgic - 1
66. TurbosaurusRX
67. Nashman69g - 1
68. Selonari - 1
69. Neutron - 1
70. Stivat - 1
71. Sgtblue -1
72. mcon (Ireland) - 1
73. BlackPEP - 1
74. RoboticsRacer
75. Hai-tek7 - 1
76. Monkman33
77. DnlCappy
78. Orbitalmovment
79. Helloninja - 1
80. Sideo - 1
81. yehreally - 2
82. $lacker - 1
83. Macer - 1
84. SimonFD3S - 1 (FRANCE)
85. j_man1100 - 1
86. ncx94 - 1 (France, and could dispatch here if you want to make only one shippment)
87. wazway 1
88. 1987 T2
89. REAmFC3S 1
90. M104-AMG (1)
91. Kissama (France)
92. TomU
93. Boriboost 1
94. MaczPayne 1
95. NetSeven 1
96. B-TAG - 1
97. RCCAZ 1, possibly 2
98. rotaryfdtt - 1
99. BeREv - 1 (France - Rotorhead on RX-7 France forum)
100. touki - 2
101. - dhahlen 1, possibly 2
102. cloud9 - 1
103. Moe Greene - 1
104. seipherzero - 1
105. m4drx - 1
106. Rawbz08 - 1
107. David Hayes - 1
108. Harry SB - 1 tank. California.
109. Net Seven - 1
110. primerGrey - 1, possibly 2
111. MDP - 1
112. elfking - 1 tank. California.
2. ZoomZoom - I'm in for at least 1. Maybe 2.
3. Slideways FD - 1
4. Silvertrd - 1 tank
5. jza80 - 1 tank
6. the spyder-
7. Izanami - 1 tank
8. SpeedCrazie - 1 Tank
9. photoresistor - 1 Tank
10. jsemerica - 1 Tank, maybe 2
11. Myocardial Infarction - 1 Tank
12. Rocketeerbandit - 1
13. Brekyrself - 2
14. 20005.3 - 1
15. Knotsonice - 1
16. Kensin - 1
17.Gio612
18.7krayziboi
19.#slevin
20. Fourtyounce - 2 maybe 3. Matt Gold for PreZident!
21. One for me please, Charlie
22. Redgti (James, uk) -1
23. Khan Racing - 1
24. Sigma
25. Alex Newman - 1 (UK)
26. thatdon
27. MattUK (UK - Can post to a mate state side if required)
28. Ptrhahn. 1
29. Iantboyd - 1
30. Fendamonky - 1
31. Sc0rp7 - 1
32. ColdFeet - 1
33. jkstill
34. Montego -1
35. Zepticon - 1 tank
36. Matthew Ng - 1
37. p51hellfire - 1
38. thanson90
39. s8nana - 1 (AU)
40. Runrex -
41. Garethb -1 (New Zealand)
42. Dhanson31
43. Ondabirdhouse - 1 (possibly 2)
44. Tictakman - 1
45. BaconHunter - 1
46. Trout2 - 1
47. spirit rx-7 - 1
48. Saham -1
49. Cvzg77r-1
50. pingu81 - 1
51. moshaka - 2 tanks maybe 3
52. Ryans93rx7 - 1
53. Rarotary - 1
54. TWIZTIDRX -1
55. XPT700 - 1 tank and shipping to Scotland
56. Sukisuki - 1
57. Daleclark - 1
58. Smokey The Talon - 1
59. Ghoujoumian - 1
60. Talkwrench (UK) - 1
61. red_dragon - 1
62. Street-heat7 - 1 maybe 2
63. Jonnybravo408- 1
64. THE TECH
65. KompressorLOgic - 1
66. TurbosaurusRX
67. Nashman69g - 1
68. Selonari - 1
69. Neutron - 1
70. Stivat - 1
71. Sgtblue -1
72. mcon (Ireland) - 1
73. BlackPEP - 1
74. RoboticsRacer
75. Hai-tek7 - 1
76. Monkman33
77. DnlCappy
78. Orbitalmovment
79. Helloninja - 1
80. Sideo - 1
81. yehreally - 2
82. $lacker - 1
83. Macer - 1
84. SimonFD3S - 1 (FRANCE)
85. j_man1100 - 1
86. ncx94 - 1 (France, and could dispatch here if you want to make only one shippment)
87. wazway 1
88. 1987 T2
89. REAmFC3S 1
90. M104-AMG (1)
91. Kissama (France)
92. TomU
93. Boriboost 1
94. MaczPayne 1
95. NetSeven 1
96. B-TAG - 1
97. RCCAZ 1, possibly 2
98. rotaryfdtt - 1
99. BeREv - 1 (France - Rotorhead on RX-7 France forum)
100. touki - 2
101. - dhahlen 1, possibly 2
102. cloud9 - 1
103. Moe Greene - 1
104. seipherzero - 1
105. m4drx - 1
106. Rawbz08 - 1
107. David Hayes - 1
108. Harry SB - 1 tank. California.
109. Net Seven - 1
110. primerGrey - 1, possibly 2
111. MDP - 1
112. elfking - 1 tank. California.
#208
Hey guys! Sorry for the delay, had some ups, had some downs. But we're moving forward.
So the second 3D printed prototype made it to me late last week. The quality is unreal, very, very impressed with the acralite. Only downside? It broke in shipping. Doh!
HOWEVER, before it shipped, the guy that printed it for me managed to snap some pics:
The good news is: none of the mounting points broke - so I can still test fit with the new mounting hardware. The bad news is: I can't do a bunch of planned "slosh testing". However, the printer ALSO managed to do some testing himself:
I'm really impressed with how stable the bottom sump stays. I think this should relieve any concerns about potential starvation. Remember, the primary nozzle is all the way to the bottom, below the fill level sensor. You can also run additional sensors if you so choose.
So the next step is to test fit this one as-is, I'm predicting it will be 100%. From there, we green light the mold production and then hurry up and wait!
I plan getting an official Group Buy setup, pricing announced and start taking deposits within two weeks.
So the second 3D printed prototype made it to me late last week. The quality is unreal, very, very impressed with the acralite. Only downside? It broke in shipping. Doh!
HOWEVER, before it shipped, the guy that printed it for me managed to snap some pics:
The good news is: none of the mounting points broke - so I can still test fit with the new mounting hardware. The bad news is: I can't do a bunch of planned "slosh testing". However, the printer ALSO managed to do some testing himself:
I'm really impressed with how stable the bottom sump stays. I think this should relieve any concerns about potential starvation. Remember, the primary nozzle is all the way to the bottom, below the fill level sensor. You can also run additional sensors if you so choose.
So the next step is to test fit this one as-is, I'm predicting it will be 100%. From there, we green light the mold production and then hurry up and wait!
I plan getting an official Group Buy setup, pricing announced and start taking deposits within two weeks.
The following users liked this post:
THE TECH (08-16-17)
#210
Junior Member
Hey guys! Sorry for the delay, had some ups, had some downs. But we're moving forward.
So the second 3D printed prototype made it to me late last week. The quality is unreal, very, very impressed with the acralite. Only downside? It broke in shipping. Doh!
HOWEVER, before it shipped, the guy that printed it for me managed to snap some pics:
The good news is: none of the mounting points broke - so I can still test fit with the new mounting hardware. The bad news is: I can't do a bunch of planned "slosh testing". However, the printer ALSO managed to do some testing himself:
https://www.youtube.com/watch?v=p8XsONejNAo
I'm really impressed with how stable the bottom sump stays. I think this should relieve any concerns about potential starvation. Remember, the primary nozzle is all the way to the bottom, below the fill level sensor. You can also run additional sensors if you so choose.
So the next step is to test fit this one as-is, I'm predicting it will be 100%. From there, we green light the mold production and then hurry up and wait!
I plan getting an official Group Buy setup, pricing announced and start taking deposits within two weeks.
So the second 3D printed prototype made it to me late last week. The quality is unreal, very, very impressed with the acralite. Only downside? It broke in shipping. Doh!
HOWEVER, before it shipped, the guy that printed it for me managed to snap some pics:
The good news is: none of the mounting points broke - so I can still test fit with the new mounting hardware. The bad news is: I can't do a bunch of planned "slosh testing". However, the printer ALSO managed to do some testing himself:
https://www.youtube.com/watch?v=p8XsONejNAo
I'm really impressed with how stable the bottom sump stays. I think this should relieve any concerns about potential starvation. Remember, the primary nozzle is all the way to the bottom, below the fill level sensor. You can also run additional sensors if you so choose.
So the next step is to test fit this one as-is, I'm predicting it will be 100%. From there, we green light the mold production and then hurry up and wait!
I plan getting an official Group Buy setup, pricing announced and start taking deposits within two weeks.
#212
needs more track time...
iTrader: (13)
Might want to try a slosh test with less than half-full, e.g. one quarter, one eighth. Can you 3-D print some small horizontal baffles just around the top of the sump area? It might help with lateral g's, should you find an issue.
--- ---
| |
| |
--------
#214
Second that!!
Might want to try a slosh test with less than half-full, e.g. one quarter, one eighth. Can you 3-D print some small horizontal baffles just around the top of the sump area? It might help with lateral g's, should you find an issue.
--- ---
| |
| |
--------
Might want to try a slosh test with less than half-full, e.g. one quarter, one eighth. Can you 3-D print some small horizontal baffles just around the top of the sump area? It might help with lateral g's, should you find an issue.
--- ---
| |
| |
--------
I could 3D print anything - but the ultimate production method (blow molding) won't allow for baffles. We already went down that route and thus why we settled on additional nozzle bosses.
#216
Rotary Enthusiast
iTrader: (9)
I think that the best way to reduce slosh might end up being to just jam a few small pieces of fuel cell foam through the opening and towards the center of the tank (using a curved metal rod or something). It doesn't really matter if they go all the way to their intended destination, as long as they compartmentalize the tank while still allowing fluid passage through at an appropriate rate
#217
If memory serves, final production will be all one piece
I think that the best way to reduce slosh might end up being to just jam a few small pieces of fuel cell foam through the opening and towards the center of the tank (using a curved metal rod or something). It doesn't really matter if they go all the way to their intended destination, as long as they compartmentalize the tank while still allowing fluid passage through at an appropriate rate
I think that the best way to reduce slosh might end up being to just jam a few small pieces of fuel cell foam through the opening and towards the center of the tank (using a curved metal rod or something). It doesn't really matter if they go all the way to their intended destination, as long as they compartmentalize the tank while still allowing fluid passage through at an appropriate rate
Good idea on the fuel cell foam. That or secondary nozzles if you're concerned. But I have to imagine 99% of people will be fine with the one nozzle / one level sensor as-is.
#218
needs more track time...
iTrader: (13)
I certainly will be happy with whatever you decide, and I think everyone understands it is your call. So take the following as suggestions only, to be accepted or rejected:
The ability to experiment with baffles after installation might be a strong argument for a two piece design, and worth the extra cost. Reviewing the difficulty and many different approaches to gas tank baffling for the FD may show it is a far from easy problem to fully anticipate the worst case a priori, with vibrations, splash, wave interference, and heavy draw out of the sump, all at the same time.
Obviously, lateral g's are the most significant concern, and the tank is long in exactly that direction.
A two piece design does introduce the need for a good seal, but given the excellent liquid gasket materials available today, that seems like a solvable problem.
#219
Again, thanks for doing this, and I apologize for not recalling that from prior posts.
I certainly will be happy with whatever you decide, and I think everyone understands it is your call. So take the following as suggestions only, to be accepted or rejected:
The ability to experiment with baffles after installation might be a strong argument for a two piece design, and worth the extra cost. Reviewing the difficulty and many different approaches to gas tank baffling for the FD may show it is a far from easy problem to fully anticipate the worst case a priori, with vibrations, splash, wave interference, and heavy draw out of the sump, all at the same time.
Obviously, lateral g's are the most significant concern, and the tank is long in exactly that direction.
A two piece design does introduce the need for a good seal, but given the excellent liquid gasket materials available today, that seems like a solvable problem.
I certainly will be happy with whatever you decide, and I think everyone understands it is your call. So take the following as suggestions only, to be accepted or rejected:
The ability to experiment with baffles after installation might be a strong argument for a two piece design, and worth the extra cost. Reviewing the difficulty and many different approaches to gas tank baffling for the FD may show it is a far from easy problem to fully anticipate the worst case a priori, with vibrations, splash, wave interference, and heavy draw out of the sump, all at the same time.
Obviously, lateral g's are the most significant concern, and the tank is long in exactly that direction.
A two piece design does introduce the need for a good seal, but given the excellent liquid gasket materials available today, that seems like a solvable problem.
In all seriousness, for those that really, really have issues with slosh after initial use, I think the first step will be multiple nozzles with pick ups placed throughout the tank. That's going to solve 99% of any issues and those issues are going to but in the 1% of extreme use.
A second solution could be adding a baffle after the fact - but wouldn't require cutting the tank in two.
Simply slitting the side of the tank and inserting a baffle would be your best solution.
After these make it out into the wild - I'd be more then happy to share the CAD files and/or exact dimensions of what a baffle would be.
How's that sound?
#222
Long time on-looker
iTrader: (33)
Not sure I understand the idea of having 2 draw points for the injection pump. Are you saying run a Y fitting of some sort to 2 different tank locations and then back to the single injection pump? I've never seen that done, so would it cause issues with the pump losing prime if one became uncovered during slosh? I'd think the uncovered location would beco,s the path of least resistance and the pump would suck air.
Or are you suggesting a full second pump and feed as a double redundant system?
Any idea how much fluid was in the tank during the test sloshes? My thought was that I'd run one single pickup point and make sure the tank was topped up before every track session. I currently use about 1/2-3/4 gallon during a 30 min session so if the capacity is 2 gallons that should give me enough remaining to not get air hopefully.
Or are you suggesting a full second pump and feed as a double redundant system?
Any idea how much fluid was in the tank during the test sloshes? My thought was that I'd run one single pickup point and make sure the tank was topped up before every track session. I currently use about 1/2-3/4 gallon during a 30 min session so if the capacity is 2 gallons that should give me enough remaining to not get air hopefully.
#223
Not sure I understand the idea of having 2 draw points for the injection pump. Are you saying run a Y fitting of some sort to 2 different tank locations and then back to the single injection pump? I've never seen that done, so would it cause issues with the pump losing prime if one became uncovered during slosh? I'd think the uncovered location would beco,s the path of least resistance and the pump would suck air.
Or are you suggesting a full second pump and feed as a double redundant system?
Any idea how much fluid was in the tank during the test sloshes? My thought was that I'd run one single pickup point and make sure the tank was topped up before every track session. I currently use about 1/2-3/4 gallon during a 30 min session so if the capacity is 2 gallons that should give me enough remaining to not get air hopefully.
Or are you suggesting a full second pump and feed as a double redundant system?
Any idea how much fluid was in the tank during the test sloshes? My thought was that I'd run one single pickup point and make sure the tank was topped up before every track session. I currently use about 1/2-3/4 gallon during a 30 min session so if the capacity is 2 gallons that should give me enough remaining to not get air hopefully.
I've seen some setups that run dual nozzles, so I wanted to be sure we accounted for that in the design - thus the additional nozzle bosses. That said, I think 99% of the people out there will run a single nozzle on the side/bottom below the level sensor. One, it's the lowest point in the tank and two, multiple nozzles are only needed for the most extreme driving situations.
As for how people would run multiple nozzles - that's really dependent on what meth injection kit you were running... and how you were running it. In a perfect, over engineered world, you'd probably run some sort of swirl pot. Two nozzles feed into one central tank, then out from there. However, I'm sure there are simpler ways to run this with Y connectors and check valves.
All that said, I think the multiple nozzles will be for the .01% of people that are in extremely extreme situations.
The tank itself is looking to hold 2+ Gallons (7.5 liters). It's a TON of juice. Running to below 1/2 a tank is going to take a LONG time. If you're drinking 1/2-3/4 gallon every 30min session, that's 3-4 sessions without topping it off, which I can't imagine happening. For a street car that's not a WOT nearly as much as a car in session, this should be more than adequate.
#224
Brings Order to Chaos
iTrader: (18)
1. Spalato - 2 tanks
2. ZoomZoom - I'm in for at least 1. Maybe 2.
3. Slideways FD - 1
4. Silvertrd - 1 tank
5. jza80 - 1 tank
6. the spyder-
7. Izanami - 1 tank
8. SpeedCrazie - 1 Tank
9. photoresistor - 1 Tank
10. jsemerica - 1 Tank, maybe 2
11. Myocardial Infarction - 1 Tank
12. Rocketeerbandit - 1
13. Brekyrself - 2
14. 20005.3 - 1
15. Knotsonice - 1
16. Kensin - 1
17.Gio612
18.7krayziboi
19.#slevin
20. Fourtyounce - 2 maybe 3. Matt Gold for PreZident!
21. One for me please, Charlie
22. Redgti (James, uk) -1
23. Khan Racing - 1
24. Sigma
25. Alex Newman - 1 (UK)
26. thatdon
27. MattUK (UK - Can post to a mate state side if required)
28. Ptrhahn. 1
29. Iantboyd - 1
30. Fendamonky - 1
31. Sc0rp7 - 1
32. ColdFeet - 1
33. jkstill
34. Montego -1
35. Zepticon - 1 tank
36. Matthew Ng - 1
37. p51hellfire - 1
38. thanson90
39. s8nana - 1 (AU)
40. Runrex -
41. Garethb -1 (New Zealand)
42. Dhanson31
43. Ondabirdhouse - 1 (possibly 2)
44. Tictakman - 1
45. BaconHunter - 1
46. Trout2 - 1
47. spirit rx-7 - 1
48. Saham -1
49. Cvzg77r-1
50. pingu81 - 1
51. moshaka - 2 tanks maybe 3
52. Ryans93rx7 - 1
53. Rarotary - 1
54. TWIZTIDRX -1
55. XPT700 - 1 tank and shipping to Scotland
56. Sukisuki - 1
57. Daleclark - 1
58. Smokey The Talon - 1
59. Ghoujoumian - 1
60. Talkwrench (UK) - 1
61. red_dragon - 1
62. Street-heat7 - 1 maybe 2
63. Jonnybravo408- 1
64. THE TECH
65. KompressorLOgic - 1
66. TurbosaurusRX
67. Nashman69g - 1
68. Selonari - 1
69. Neutron - 1
70. Stivat - 1
71. Sgtblue -1
72. mcon (Ireland) - 1
73. BlackPEP - 1
74. RoboticsRacer
75. Hai-tek7 - 1
76. Monkman33
77. DnlCappy
78. Orbitalmovment
79. Helloninja - 1
80. Sideo - 1
81. yehreally - 2
82. $lacker - 1
83. Macer - 1
84. SimonFD3S - 1 (FRANCE)
85. j_man1100 - 1
86. ncx94 - 1 (France, and could dispatch here if you want to make only one shippment)
87. wazway 1
88. 1987 T2
89. REAmFC3S 1
90. M104-AMG (1)
91. Kissama (France)
92. TomU
93. Boriboost 1
94. MaczPayne 1
95. NetSeven 1
96. B-TAG - 1
97. RCCAZ 1, possibly 2
98. rotaryfdtt - 1
99. BeREv - 1 (France - Rotorhead on RX-7 France forum)
100. touki - 2
101. - dhahlen 1, possibly 2
102. cloud9 - 1
103. Moe Greene - 1
104. seipherzero - 1
105. m4drx - 1
106. Rawbz08 - 1
107. David Hayes - 1
108. Harry SB - 1 tank. California.
109. Net Seven - 1
110. primerGrey - 1, possibly 2
111. MDP - 1
112. elfking - 1 tank. California.
113. technomentor - 1, possibly 2
2. ZoomZoom - I'm in for at least 1. Maybe 2.
3. Slideways FD - 1
4. Silvertrd - 1 tank
5. jza80 - 1 tank
6. the spyder-
7. Izanami - 1 tank
8. SpeedCrazie - 1 Tank
9. photoresistor - 1 Tank
10. jsemerica - 1 Tank, maybe 2
11. Myocardial Infarction - 1 Tank
12. Rocketeerbandit - 1
13. Brekyrself - 2
14. 20005.3 - 1
15. Knotsonice - 1
16. Kensin - 1
17.Gio612
18.7krayziboi
19.#slevin
20. Fourtyounce - 2 maybe 3. Matt Gold for PreZident!
21. One for me please, Charlie
22. Redgti (James, uk) -1
23. Khan Racing - 1
24. Sigma
25. Alex Newman - 1 (UK)
26. thatdon
27. MattUK (UK - Can post to a mate state side if required)
28. Ptrhahn. 1
29. Iantboyd - 1
30. Fendamonky - 1
31. Sc0rp7 - 1
32. ColdFeet - 1
33. jkstill
34. Montego -1
35. Zepticon - 1 tank
36. Matthew Ng - 1
37. p51hellfire - 1
38. thanson90
39. s8nana - 1 (AU)
40. Runrex -
41. Garethb -1 (New Zealand)
42. Dhanson31
43. Ondabirdhouse - 1 (possibly 2)
44. Tictakman - 1
45. BaconHunter - 1
46. Trout2 - 1
47. spirit rx-7 - 1
48. Saham -1
49. Cvzg77r-1
50. pingu81 - 1
51. moshaka - 2 tanks maybe 3
52. Ryans93rx7 - 1
53. Rarotary - 1
54. TWIZTIDRX -1
55. XPT700 - 1 tank and shipping to Scotland
56. Sukisuki - 1
57. Daleclark - 1
58. Smokey The Talon - 1
59. Ghoujoumian - 1
60. Talkwrench (UK) - 1
61. red_dragon - 1
62. Street-heat7 - 1 maybe 2
63. Jonnybravo408- 1
64. THE TECH
65. KompressorLOgic - 1
66. TurbosaurusRX
67. Nashman69g - 1
68. Selonari - 1
69. Neutron - 1
70. Stivat - 1
71. Sgtblue -1
72. mcon (Ireland) - 1
73. BlackPEP - 1
74. RoboticsRacer
75. Hai-tek7 - 1
76. Monkman33
77. DnlCappy
78. Orbitalmovment
79. Helloninja - 1
80. Sideo - 1
81. yehreally - 2
82. $lacker - 1
83. Macer - 1
84. SimonFD3S - 1 (FRANCE)
85. j_man1100 - 1
86. ncx94 - 1 (France, and could dispatch here if you want to make only one shippment)
87. wazway 1
88. 1987 T2
89. REAmFC3S 1
90. M104-AMG (1)
91. Kissama (France)
92. TomU
93. Boriboost 1
94. MaczPayne 1
95. NetSeven 1
96. B-TAG - 1
97. RCCAZ 1, possibly 2
98. rotaryfdtt - 1
99. BeREv - 1 (France - Rotorhead on RX-7 France forum)
100. touki - 2
101. - dhahlen 1, possibly 2
102. cloud9 - 1
103. Moe Greene - 1
104. seipherzero - 1
105. m4drx - 1
106. Rawbz08 - 1
107. David Hayes - 1
108. Harry SB - 1 tank. California.
109. Net Seven - 1
110. primerGrey - 1, possibly 2
111. MDP - 1
112. elfking - 1 tank. California.
113. technomentor - 1, possibly 2