General Rotary Tech Support Use this forum for tech questions not specific to a certain model year
Sponsored by:
Sponsored by: CARiD

Am I in trouble ?

Thread Tools
 
Search this Thread
 
Old May 13, 2003 | 10:21 AM
  #1  
Rubik1's Avatar
Thread Starter
Newbie
 
Joined: May 2003
Posts: 2
Likes: 0
From: Malaysia
Am I in trouble ?

Hello guys, i'd like to hear your opinion on what has gone wrong to my car ! I own a 93 RX-7 TT , and recently, the car overheated badly. I'm talking overheated till there was not a single drop of water left in the radiator (it all leaked out) . I only noticed it when i pulled over and tried to restart the engine after shuting it down briefly, and it would NOT start , and sure enough, the temp. meter was off the scale, all the way till the end. Now that everything is back to "normal" , I am having extreme problem starting the car. It would crank and crank and crank and takes forever before it would start up. These are the symptoms. Can someone explain to me what possible problems i'm facing ?
Reply
Old May 13, 2003 | 12:19 PM
  #2  
Josepi's Avatar
Despise Enmity
Tenured Member 20 Years
 
Joined: May 2001
Posts: 2,420
Likes: 0
From: Richmond, VA
When it eventually does crank, do you get white smoke from the exhaust?
Reply
Old May 13, 2003 | 02:49 PM
  #3  
jeremy's Avatar
male stripper
Tenured Member 15 Years
iTrader: (1)
 
Joined: Oct 2001
Posts: 3,126
Likes: 1
From: St Petersburg, FL
you have warped the motor. its basically a sandwich of different metals and each expands at a different rate/amount. check your oil for gas and your exhaust for white/blue smoke.
Reply
Old May 13, 2003 | 10:15 PM
  #4  
Rubik1's Avatar
Thread Starter
Newbie
 
Joined: May 2003
Posts: 2
Likes: 0
From: Malaysia
What do you mean by "check your oil for gas" ?
Reply
Old May 14, 2003 | 08:58 AM
  #5  
jeremy's Avatar
male stripper
Tenured Member 15 Years
iTrader: (1)
 
Joined: Oct 2001
Posts: 3,126
Likes: 1
From: St Petersburg, FL
typically the center "bowls", is no longer flat. the side seals won't effectively contact te plates and will allow the compression to push mixture into the center of the rotor and into the oil. so when you change the oil see if there is any gas in it as it is a sign that the plates are warped and you will need a rebuild soon.
Reply
Old May 16, 2003 | 08:29 AM
  #6  
vudoodoodoo's Avatar
Rotary Freak
Tenured Member 10 Years
 
Joined: Aug 2001
Posts: 1,635
Likes: 0
From: Boston, MA
Rebuild time...
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
FC3S Timmy
2nd Generation Specific (1986-1992)
16
Oct 3, 2015 01:08 AM
Rotafuzz
New Member RX-7 Technical
3
Sep 30, 2015 09:55 AM
Red-Dragon_Akuma
New Member RX-7 Technical
11
Sep 28, 2015 06:09 AM
blackball7
2nd Generation Specific (1986-1992)
9
Sep 20, 2015 08:33 PM
WANKfactor
Single Turbo RX-7's
7
Sep 15, 2015 07:45 AM




All times are GMT -5. The time now is 10:13 PM.