RX7Club.com - Mazda RX7 Forum
0 2024/08/24 17:38:00
0 2024/08/24 17:37:56
0 2022/09/03 00:27:05
0 2022/09/03 00:26:57
0 2022/09/03 00:26:47
0 2022/09/03 00:26:39
0 2022/08/16 19:20:36
Is this the one we want to use? People say use duplicolor plastic vinyl but this is the one that comes up
Is this the one we want to use? People say use duplicolor plastic vinyl but this is the one that comes up
0 2022/08/16 19:20:00
0 2022/08/16 19:19:47
0 2022/08/16 19:16:58
0 2022/08/16 19:16:01
0 2022/07/21 10:14:01
0 2022/07/21 10:13:54
0 2022/07/21 10:13:48
0 2022/07/21 10:13:40
0 2022/07/21 10:13:34
0 2022/07/21 10:13:25
0 2022/07/21 10:13:14
0 2022/07/21 10:12:59
0 2022/07/21 10:12:49
0 2022/07/21 10:12:41
0 2022/07/21 10:12:19
0 2022/07/21 10:12:07
0 2022/07/21 10:06:22
0 2022/07/21 10:06:11
0 2022/07/21 10:05:59
Manifold and wastegatw
Manifold and wastegatw
0 2022/07/21 09:46:15
0 2022/07/17 15:24:26
0 2022/07/17 15:23:58
0 2022/07/16 19:01:28
0 2022/07/16 19:01:23
0 2022/07/16 19:01:17
0 2022/07/16 19:01:13
0 2022/07/16 18:56:09
0 2022/07/16 14:57:58
0 2022/07/16 14:57:54
On the pulley bracket There is a little space where the stud goes into the water pump. I wanted to let it sit flush so I added a washer. Used the supplied long bolt (to replace the stock stud and nut) but as you can see the bolt head is hitting touching the water pump pulley (blue)…
On the pulley bracket There is a little space where the stud goes into the water pump. I wanted to let it sit flush so I added a washer. Used the supplied long bolt (to replace the stock stud and nut) but as you can see the bolt head is hitting touching the water pump pulley (blue)…
0 2022/07/16 14:57:49
So got everything on there. The small Allen bolt right side of bracket is easily stripped and unfortunately stripped on me. Would recommend to find and use a regular stainless bolt m6-1.0-30mm
So got everything on there. The small Allen bolt right side of bracket is easily stripped and unfortunately stripped on me. Would recommend to find and use a regular stainless bolt m6-1.0-30mm
0 2022/07/16 14:57:45
Is this the right orientation? It would seem with the circular raised bevels (the bearing would sit on it)? But in the directions it says the pineapple racing logo should face the front?? Then that would make this raised circular bevel face the back..
Is this the right orientation? It would seem with the circular raised bevels (the bearing would sit on it)? But in the directions it says the pineapple racing logo should face the front?? Then that would make this raised circular bevel face the back..
0 2022/07/16 14:57:41
0 2022/07/16 14:53:13