RX7Club.com - Mazda RX7 Forum
0 2016/12/15 18:41:13
Front cover installed
Front cover installed
0 2016/12/15 18:40:26
0 2016/12/13 01:17:10
Gave Cosmo #1 a wash and took it for a drive
Gave Cosmo #1 a wash and took it for a drive
0 2016/12/13 01:16:19
0 2016/12/13 01:12:58
Gave Cosmo #1 a wash and took it for a drive
Gave Cosmo #1 a wash and took it for a drive
0 2016/12/13 01:12:12
0 2016/12/13 01:09:28
Gave cosmo #1 a wash and took it for a drive.
Gave cosmo #1 a wash and took it for a drive.
0 2016/12/13 01:08:21
Set the endplay, was able to use a spacer i had laying which was easy.
Set the endplay, was able to use a spacer i had laying which was easy.
0 2016/12/13 01:05:57
0 2016/12/13 01:03:13
A completed 4 rotor apart from front stack.
A completed 4 rotor apart from front stack.
0 2016/12/10 13:55:04
0 2016/12/10 13:54:36
#4 rotor
#4 rotor
0 2016/12/10 13:53:58
0 2016/12/10 13:53:28
0 2016/12/10 13:52:57
#3 rotor
#3 rotor
0 2016/12/10 13:52:13
Thought getting this center plate on would be a bit tricky, but it pretty much fell into place.
Thought getting this center plate on would be a bit tricky, but it pretty much fell into place.
0 2016/12/10 13:50:12
0 2016/12/10 13:49:44
0 2016/12/10 13:49:06
#1 rotor
#1 rotor
0 2016/12/10 13:48:18
View of the stationary gear mod
View of the stationary gear mod
0 2016/12/10 13:47:19
All seals fitted, ready for assembly.
All seals fitted, ready for assembly.
0 2016/12/08 19:44:34
Its nice working with brand new parts.
Its nice working with brand new parts.
0 2016/12/08 19:43:41
0 2016/12/08 19:43:17
0 2016/12/08 19:42:53
All seals clearanced ready to be fitted to the rotors
All seals clearanced ready to be fitted to the rotors
0 2016/12/08 19:41:57
Clearancing side seals. Set up this jig on the drill press using a scrap rotor. The grinding wheel is for a dremel. Used the fastest speed on the drill and it worked really well.
Clearancing side seals. Set up this jig on the drill press using a scrap rotor. The grinding wheel is for a dremel. Used the fastest speed on the drill and it worked really well.
0 2016/12/04 19:26:19
Machining the out oil groove in the rotor bearings.
Machining the out oil groove in the rotor bearings.
0 2016/12/04 19:24:00
Got the rotating assembly balanced and rotors side clearanced, thanks to Grant at Rotorsport Racing & Engine Balancing.
Got the rotating assembly balanced and rotors side clearanced, thanks to Grant at Rotorsport Racing & Engine Balancing.
0 2016/12/04 19:20:07
Seals and springs
Seals and springs
0 2016/12/04 19:19:06
0 2016/12/04 19:18:13
0 2016/11/29 15:53:16
0 2016/11/29 15:52:51
Painted the plates with this stuff. Seems a lot tougher than other spray paints i've used.
Painted the plates with this stuff. Seems a lot tougher than other spray paints i've used.
0 2016/11/29 15:49:30
NRS apex seals 1 piece 2mm x 12
NRS apex seals 1 piece 2mm x 12
0 2016/11/25 13:53:13
The coating is durable enough to coat fastners with.
The coating is durable enough to coat fastners with.
0 2016/11/25 13:51:58
Did the CAS aswell
Did the CAS aswell
0 2016/11/25 13:51:17
0 2016/11/25 13:50:53
Finished
Finished
0 2016/11/25 13:50:16
Parts are then cooked for 10mins at 200°c.
Parts are then cooked for 10mins at 200°c.
0 2016/11/25 13:49:12