RX7Club.com - Mazda RX7 Forum
0 2016/12/11 15:02:00
0 2016/12/11 15:01:59
0 2016/12/11 15:01:57
0 2016/12/11 15:01:56
0 2016/12/11 15:01:56
0 2016/12/11 15:01:55
0 2016/12/11 15:01:54
0 2016/12/11 15:01:53
0 2016/12/11 15:01:52
0 2016/12/11 15:01:51
0 2016/12/11 15:01:50
0 2016/12/11 15:01:49
0 2016/12/11 15:01:48
0 2016/10/09 18:16:58
0 2016/10/09 18:12:29
0 2016/10/09 18:12:28
0 2016/10/09 18:12:28
0 2016/10/09 18:12:27
0 2016/09/30 08:07:52
0 2016/09/30 08:04:45
0 2016/09/30 08:03:28
0 2016/09/30 08:02:16
0 2016/09/30 08:02:15
0 2016/09/30 08:02:13
0 2016/09/30 07:58:40
0 2016/09/30 07:57:40
0 2016/09/30 07:56:23
Had some more issues with this car towards the end of the day. For some reason, I was missing an axle boot clamp? DIdn't notice it until there was grease everywhere in my wheel. Used a zip tie as a temp, and ran my last session. Gotta take it out and regrease. Grease looked milky.
Had some more issues with this car towards the end of the day. For some reason, I was missing an axle boot clamp? DIdn't notice it until there was grease everywhere in my wheel. Used a zip tie as a temp, and ran my last session. Gotta take it out and regrease. Grease looked milky.
0 2016/07/10 11:12:24
Henry was out there passing everyone.
Henry was out there passing everyone.
0 2016/07/10 11:12:18
Brett's 20b rx-3, sounds mean!
Brett's 20b rx-3, sounds mean!
0 2016/07/10 11:12:13
Everything went back in smoothly, and car fired right up.
Everything went back in smoothly, and car fired right up.
0 2016/07/10 11:12:07
That center locking piece was melted on as one piece on the old one. Had to dremel the whole connector because it was glued together, then saved that center locking piece because Fris didn't have it.
That center locking piece was melted on as one piece on the old one. Had to dremel the whole connector because it was glued together, then saved that center locking piece because Fris didn't have it.
0 2016/07/10 11:12:03
Here's the connector I burned on my downpipe.
Here's the connector I burned on my downpipe.
0 2016/07/10 11:11:59
Here's the temps we've been seeing all day. We ran the car really hard. Had some issues with either the water temp correction map not accounting for water temps above 180, or my fuel was getting too hot(external pump) causing me to run lean. This would happen in a corner, and my tank was full. We adjusted the water temp correction map to add 5% more fuel in those upper regions.
Here's the temps we've been seeing all day. We ran the car really hard. Had some issues with either the water temp correction map not accounting for water temps above 180, or my fuel was getting too hot(external pump) causing me to run lean. This would happen in a corner, and my tank was full. We adjusted the water temp correction map to add 5% more fuel in those upper regions.
0 2016/07/10 11:11:44
SSR Reverse Mesh. 17x8.5+22, 17x9.5+35. Planning on running some Federal RS-RR as my autocross/street wheels.
SSR Reverse Mesh. 17x8.5+22, 17x9.5+35. Planning on running some Federal RS-RR as my autocross/street wheels.
0 2016/07/07 20:40:49
Alex fabbing up custom mounts
Alex fabbing up custom mounts
0 2016/07/07 20:39:51
Here you can see the new seats installed, new harnesses and my really expensive 4pt roll bar.
Here you can see the new seats installed, new harnesses and my really expensive 4pt roll bar.
0 2016/07/07 20:39:01
Here, you can the old seat shoved in there with the a pillar bar there. Literally had to smash the seat to get it in there to move the car.
Here, you can the old seat shoved in there with the a pillar bar there. Literally had to smash the seat to get it in there to move the car.
0 2016/07/07 20:37:38
0 2015/11/18 19:46:51
0 2015/11/18 19:46:50