RX7Club.com - Mazda RX7 Forum
0 2020/10/30 13:54:08
0 2021/01/19 02:41:39
0 2021/01/19 02:41:49
0 2021/01/19 02:41:58
0 2021/01/19 09:48:40
0 2021/01/19 09:48:51
0 2021/01/19 09:48:58
For the front holes my dad made some threads that have a sharp point to mark the front two holes
For the front holes my dad made some threads that have a sharp point to mark the front two holes
0 2021/01/23 07:12:42
I scaled the drill template to the correct size and aligned the two rear holes
I scaled the drill template to the correct size and aligned the two rear holes
0 2021/01/23 07:12:49
Came out great
Came out great
0 2021/01/23 07:12:56
0 2021/01/23 07:13:05
I still have to buy a new seal for the bottom of the mounts so which I will fit after the everything is painted .
I still have to buy a new seal for the bottom of the mounts so which I will fit after the everything is painted .
0 2021/01/23 07:13:12
0 2021/01/23 07:13:20
Very happy to have my dad to help me finish Building the car
Very happy to have my dad to help me finish Building the car
0 2021/01/23 07:13:26
0 2021/01/25 22:29:43
0 2021/01/25 22:32:50
0 2021/01/25 22:32:58
0 2021/01/25 22:33:06
0 2021/01/25 22:33:14
0 2021/01/25 22:33:21
0 2021/01/25 22:33:28
0 2021/01/25 22:33:37
0 2021/01/25 22:33:44
0 2021/01/25 22:33:52
0 2021/01/25 22:36:35
0 2021/01/25 23:47:35
0 2021/01/26 00:52:20
0 2021/01/26 00:52:28
CX Racing V-Mount Radiator just arrived
CX Racing V-Mount Radiator just arrived
0 2021/01/26 04:19:58
0 2021/01/29 01:33:55
0 2021/01/31 12:57:29
0 2021/01/31 12:57:37
0 2021/01/31 12:57:44
0 2021/01/31 12:58:22
A bit of dress up
A bit of dress up
0 2021/02/05 23:32:19
Some temporary brackets to figure out the final angle on the radiator
Some temporary brackets to figure out the final angle on the radiator
0 2021/02/05 23:32:27
My new dad hard at work measuring up the brackets
My new dad hard at work measuring up the brackets
0 2021/02/05 23:32:34
0 2021/02/05 23:32:41
Bought a used scrap harness on eBay that I can use as a template
Bought a used scrap harness on eBay that I can use as a template
0 2021/02/14 01:56:24
Also did some more work in the pedal adapter . I moved the pedal a bit further down as wasn’t happy with the position . The spacers are still 3D printed and will be most probably made out of Aluminium or Polyamid later .
Also did some more work in the pedal adapter . I moved the pedal a bit further down as wasn’t happy with the position . The spacers are still 3D printed and will be most probably made out of Aluminium or Polyamid later .
0 2021/02/14 01:56:34