RX7Club.com - Mazda RX7 Forum
Just before welding
Just before welding
0 2011/02/08 12:16:17
This is a quicky collector. Mild steel will be replaced with Stainless.
This is a quicky collector. Mild steel will be replaced with Stainless.
0 2011/02/08 12:16:17
Stripping spring perch off the strut for coil over set up. You can see my simple solution for brake cooling. 2 cuts to the backing plate and bend it out. This is a cheep eazy fix. When there is time I will do it right. I still use cool air tubes directed into the vents.
Stripping spring perch off the strut for coil over set up. You can see my simple solution for brake cooling. 2 cuts to the backing plate and bend it out. This is a cheep eazy fix. When there is time I will do it right. I still use cool air tubes directed into the vents.
0 2011/02/08 12:16:17
I made this ring to take up some of the slack between the strut tube and the 2" coil over sleve.
I made this ring to take up some of the slack between the strut tube and the 2" coil over sleve.
2 2011/02/08 12:20:10
ou can see the sleve welded in place
ou can see the sleve welded in place
0 2011/02/08 12:20:10
Strut ready for the coil over
Strut ready for the coil over
2 2011/02/08 12:20:10
Collector welded up
Collector welded up
0 2011/02/11 08:37:05
Test fit
Test fit
0 2011/02/11 08:37:05
now I need to bolt it on to check the clearance
now I need to bolt it on to check the clearance
0 2011/02/11 08:37:05
IMG 0589
IMG 0589
0 2011/02/14 01:23:53
Seem to fit nice, but looks like I'm going to run straight pipe, no Muffler fot the fist race.
Seem to fit nice, but looks like I'm going to run straight pipe, no Muffler fot the fist race.
0 2011/02/21 10:30:48
30" primarys to a 2.5" collector back to 3" section. Back to a 2.5". This is for a stock port 12a with a weber 48 ida. All ready for welding the tail pipe.
30" primarys to a 2.5" collector back to 3" section. Back to a 2.5". This is for a stock port 12a with a weber 48 ida. All ready for welding the tail pipe.
0 2011/02/21 10:30:48
4 2011/02/21 10:30:48
Mar 05 Nasa Race Group C Race 320pm CP4 1311
Mar 05 Nasa Race Group C Race 320pm CP4 1311
0 2011/03/08 12:05:59
Struts installed
Struts installed
0 2011/03/20 07:07:02
Bump steer spacer and sway bar end links installed
Bump steer spacer and sway bar end links installed
0 2011/03/20 07:07:02
Mar 06 Nasa Race Group C
Mar 06 Nasa Race Group C
0 2011/03/20 07:24:25
This radiator has a straight outlet on the bottom. I found a NAPA hose to directly fit after triming it to size. P/N 9494
This radiator has a straight outlet on the bottom. I found a NAPA hose to directly fit after triming it to size. P/N 9494
0 2011/04/18 00:35:31
Radiator still needs to be trimed
Radiator still needs to be trimed
0 2011/04/18 00:35:31
New Aluminum radiator and mounts
New Aluminum radiator and mounts
0 2011/04/18 00:35:31
Getting ready for the weekend
Getting ready for the weekend
0 2011/04/18 00:48:41
Started in 6th passed 2 for 4th
Started in 6th passed 2 for 4th
0 2011/10/16 17:21:00
Passed two more for 2nd
Passed two more for 2nd
0 2011/10/16 17:22:57
The 44 car just before he passed me and spun letting the 23 car pass me. So I went to 3rd back to 2nd back to 3rd
The 44 car just before he passed me and spun letting the 23 car pass me. So I went to 3rd back to 2nd back to 3rd
0 2011/10/16 17:24:53
Back in 2nd before slower traffic held me back and the 23 repassed me
Back in 2nd before slower traffic held me back and the 23 repassed me
0 2011/10/16 17:24:53
7s Only BIG Strut and brake set up. But I wanted to run 13's. so I adapted the 10" rotor. This is the 10" on top and the 12" on the bottom
7s Only BIG Strut and brake set up. But I wanted to run 13's. so I adapted the 10" rotor. This is the 10" on top and the 12" on the bottom
0 2014/05/04 07:59:18
Clearance at the caliper was the biggest pain.
Clearance at the caliper was the biggest pain.
0 2014/05/04 07:59:18
But when everything was done. The 13" rims fit nice.
But when everything was done. The 13" rims fit nice.
0 2014/05/04 07:59:18