RX7Club.com - Mazda RX7 Forum
linkage #3
linkage #3
0 2024/11/19 13:03:54
Note the two plastic bushings on the arm
Note the two plastic bushings on the arm
0 2024/11/19 13:04:06
bushing #2
bushing #2
0 2024/11/19 13:04:14
secondary shaft
secondary shaft
0 2024/11/19 13:04:21
SS washer #5
SS washer #5
0 2024/11/19 13:04:34
Square end and curved end attachments
Square end and curved end attachments
0 2024/11/21 16:26:04
Curved end attachments on bracket
Curved end attachments on bracket
0 2024/11/21 16:26:12
Square end attachments
Square end attachments
0 2024/11/21 16:26:28
Spring attaching bracket orientation
Spring attaching bracket orientation
0 2024/11/22 13:37:27
Bracket points to the main spring attachment bracket!
Bracket points to the main spring attachment bracket!
0 2024/11/22 13:37:58
0 2024/11/22 17:57:32
My testing hookup
My testing hookup
0 2024/11/23 13:35:44
wear point on the cam
wear point on the cam
0 2024/11/23 21:52:43
0 2024/11/23 21:56:14
wear point on cam
wear point on cam
0 2024/11/23 21:56:17
0 2024/11/28 21:14:56
TPS installed and adjusted to 1k ohms
TPS installed and adjusted to 1k ohms
0 2024/11/28 21:18:24
using spring clamps on a vacuum line
using spring clamps on a vacuum line
0 2024/11/29 16:32:59
This is Rexy, all dressed up & nowhere to go!
This is Rexy, all dressed up & nowhere to go!
0 2024/11/30 07:51:06
assembled parts
assembled parts
0 2024/12/18 20:03:21
five parts of the bracket assembly
five parts of the bracket assembly
0 2024/12/18 20:03:27
0 2024/12/22 18:50:47
0 2024/12/22 18:50:50
0 2024/12/22 18:50:52
Proper way to test the diaphragm
Proper way to test the diaphragm
0 2024/12/23 16:23:57
polished thermowax
polished thermowax
0 2024/12/26 19:49:04
Pencil to move the fast idle cam and have the throttle plates fully closed
Pencil to move the fast idle cam and have the throttle plates fully closed
0 2024/12/30 18:30:17
leather block to hold open the throttle valves
leather block to hold open the throttle valves
0 2024/12/30 18:30:21
witness marks from fully closing the throttle valve while the coating is still wet
witness marks from fully closing the throttle valve while the coating is still wet
0 2024/12/30 18:30:25
0 2025/01/03 20:00:10
0 2025/01/03 20:00:12
0 2025/01/03 20:01:15
0 2025/01/03 20:01:20
0 2025/01/03 20:01:26
0 2025/01/03 20:01:32
0 2025/01/03 20:01:38
0 2025/01/03 20:01:43
0 2025/01/03 20:01:46
reusing the new egr pin
reusing the new egr pin
0 2025/01/14 17:07:07
Rotor bearing failure at 30 mph
Rotor bearing failure at 30 mph
0 2025/01/14 20:59:47