my rx7 drift build
02-18-09, 03:42 AM
#276
Keep Up
iTrader: (6)
Join Date: Jul 2008
Location: nj
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
well ima go 18x9.5 in rear wit the bmagic wider fenders and get a fender roller from stance and roll my fenders plus i have 20mm spacers cause they guy who sold me a red t2 had them with fd wheels so i could possibly use those wut offset did u get? i just wanna see what the car looks like wit them on
02-18-09, 06:12 PM
#277
Full Member
iTrader: (1)
Join Date: May 2007
Location: South Dakota
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
man i have never seen anything like this. i can't find any words to describe your skillz
i was just wondering were did you get your 2:1 steering quickener on your rack
i have taken my manual rack off to clean n re-lube it, but i would like to add some mods to it. I 'm looking for more steering angel but I cannot find anything no adj. inner or outter tie rods or steering quickener
i guess only p/s racks have the adj tie rods
thanks your advice will be most helpful
also you have the coolest project better than anyone could ever dream of
i was just wondering were did you get your 2:1 steering quickener on your rack
i have taken my manual rack off to clean n re-lube it, but i would like to add some mods to it. I 'm looking for more steering angel but I cannot find anything no adj. inner or outter tie rods or steering quickener
i guess only p/s racks have the adj tie rods
thanks your advice will be most helpful
also you have the coolest project better than anyone could ever dream of
02-21-09, 10:37 PM
#278
Rotary Enthusiast
Join Date: Feb 2005
Location: Norway
Posts: 846
Likes: 0
Received 0 Likes
on
0 Posts
2:1 can be bought from summit-racing.com
Never seen anyone use it but i just heard that it can make the front wheels move to quick so you actually loose points for correct wheel angle all the time.. Probably fun to drive with
Never seen anyone use it but i just heard that it can make the front wheels move to quick so you actually loose points for correct wheel angle all the time.. Probably fun to drive with
02-23-09, 03:00 AM
#279
Keep Up
iTrader: (6)
Join Date: Jul 2008
Location: nj
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
http://i228.photobucket.com/albums/e...7/DSC00473.jpg
wut are these brackets u are using to hold that flange to the turbo flange
wut are these brackets u are using to hold that flange to the turbo flange
02-23-09, 05:30 PM
#281
Rotary Enthusiast
Join Date: Feb 2005
Location: Norway
Posts: 846
Likes: 0
Received 0 Likes
on
0 Posts
http://i228.photobucket.com/albums/e...7/DSC00473.jpg
wut are these brackets u are using to hold that flange to the turbo flange
wut are these brackets u are using to hold that flange to the turbo flange
02-24-09, 07:31 PM
#282
Keep Up
iTrader: (6)
Join Date: Jul 2008
Location: nj
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
yea i kno that i meant where can i go to get some of those cause i have the RB header flange too i jsut need to find something to hold the other flange and take it to a machine shop to get it welded
05-31-09, 01:34 PM
#294
pull the fenders with newspaper.
Just take a 1/4" thick chunk of it and set it on the tire.
Drop the car onto it.
presto, perfect flush. It does work and i've seen alot of good results with that method.
it's easy to overdo it with a bat/socket/anything thick and round. With newspaper it comes out perfect. You can always lower your coilover perches and adjust camber to increase the pull you want to fit your new settings by just re-doing the newspaper pull.
If you're talking about getting the lips of the fender flat, just use your palm on the front and hammer the inside. I recommend atleast a 3.5lb hammer for the rears because it's "2-ply" sheet metal and a pain in the *** with a regular hammer.
Just take a 1/4" thick chunk of it and set it on the tire.
Drop the car onto it.
presto, perfect flush. It does work and i've seen alot of good results with that method.
it's easy to overdo it with a bat/socket/anything thick and round. With newspaper it comes out perfect. You can always lower your coilover perches and adjust camber to increase the pull you want to fit your new settings by just re-doing the newspaper pull.
If you're talking about getting the lips of the fender flat, just use your palm on the front and hammer the inside. I recommend atleast a 3.5lb hammer for the rears because it's "2-ply" sheet metal and a pain in the *** with a regular hammer.
06-07-09, 05:27 AM
#296
Full Member
Join Date: Mar 2006
Location: Near Calgary
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
Correct me if I'm wrong.
07-27-09, 11:49 PM
#299
Senior Member
Thread Starter
sorry guys i got caught up making a 240 rb25 car .
lots of pics if u want to look at them about the build
http://s228.photobucket.com/albums/e...ing/rb25%20SX/
i just got done with the racefab turbo kit
this is it on my rx7.
and i cleaned the motor bay lol
going to be working on my rx7 more this week. look out for pics
lots of pics if u want to look at them about the build
http://s228.photobucket.com/albums/e...ing/rb25%20SX/
i just got done with the racefab turbo kit
this is it on my rx7.
and i cleaned the motor bay lol
going to be working on my rx7 more this week. look out for pics