Probably ~$250-300. They go new for 350+ and I've put only a couple hundred miles on this setup so that seems like a more than reasonable price range to me. When I pull it from the car I'll let you know.

Cant wait to see this in St louis. Will be cool to have two verts getting tuned although yours is going to be sick.

ur freakin awesome

tell that bodyshop to get your shit done!!!!!

Yea hows it coming along?

x100!!!

update i must see the kit on the car already lol...

i still envy you on those damn wheels!!(i admit i only see your thread just for the wheels:wallbash: )

j/k :hahaha:

I have decided to abandon this project! I am now parting out my car!

That sucks man, pm'd ya

god i hope that some day i'll be able to afford to do this...

Lies

awesome project

is this an early april fools joke?



wtf...

or did you score a sick deal on a wild new car like a Noble M12, Ultima GTR or soemthing just as delicious?!?!?

or are you pregnant with triplets?

or did you get busted for whatever and are sitting in jail?

there has to be a good reason...

Wow I read this whole thread and to hear you say this.... makes me quite upset! Though I know your joking it still has me scared...

:lol:

I can't fool some of you guys!


Filmed 3-17-2008:<object height="355" width="425">
<embed src="http://www.youtube.com/v/84IhBqDE-R8&hl=en" type="application/x-shockwave-flash" wmode="transparent" height="355" width="425">

Was filmed in High Def but obviously YouTube fucks that all up. This is the kit being test fitted. The hood is NOT fully shut in the video. I need a new latch. I stopped by the shop the following day and they were working on the front driver side fender, they had just finished fitting the passenger side with the front bumper. I didn't take any pics that day but I am gonna try to stop by there tomorrow and grab some more pics.

The door molding still needs to be deleted along with the molding on the front and rear bumpers. The vents need to be cut out still, antenna shaved, gas door installed and fill tube extended. The front bumper needs to be trimmed up a bit. Lots of work left to be done.

The kit did not originally fit as well as it does in the video now. Here is what initial fitment looked like:
http://img128.imageshack.us/img128/5641/dsc00185cp4.jpg
http://img128.imageshack.us/img128/6245/dsc00188qz6.jpg
http://img209.imageshack.us/img209/6444/dsc00190vx6.jpg




The bad weather has subsided for a while so the shop isn't so busy with the collision work that the snow brings. They have been working on my car every day this week. I should have some more pics & footage this weekend.





Here is a little preview of something I'm cookin up:
http://img178.imageshack.us/img178/5...elightsap0.jpg
</object>

Lookin good. Cant wait to see the finished product!!!

looks sick! hope to see this slammed/dropped properly to make use of the widebody/rim selection. =p

Are you going to keep those "vent" cut outs on the panals?

That's what the Tein flex coilovers are for.

ahhh ok.. i just browsed thru the pics =p

OK might be a dumb question but can you open the trunk with that wing on it?

Yes. The part of the wing that looks like it is attached to the sides of the car are actually not attached. The 2 legs in the middle of the trunk(which you cannot see in the video) are where the wing mounts. The sides have rubber gaskets attached to the bottom so that they will sit flush with the body and not vibrate. The driver side area actually has a hole for the antenna to come up through. If the antenna is up then you cannot open the trunk then. I will be shaving the antenna so that will never be a problem. I'm debating shaving that hole in the wing and reshaping it so it looks like the other side. But since that wing is so extremely rare I think I may just end up leaving it as is.


I am about to head over to the body shop right now. I'll take more pics and video.

All I can say is Dayum!!!

That thing is to wide ;)
Glad to see that the kit is working out.
pm me with more details when you get a chance.

On my end, I still have not heard a damn word.
I think he is ignoring me.

"...but can she drift"

...just be prepared for those words when you get her out of the shop... when ever that is, keep it up

<object height="350" width="425">
<embed src="http://www.youtube.com/v/bD9f7FsHyLM" type="application/x-shockwave-flash" height="350" width="425"> </object>


Driver side molding deleted. Some front bumper molding deleted. Driver side vent cut out.

Check out the gap between the driver door and front fender. Perfect!



HaHa, do you get that alot?



PM coming.

What spoiler is that? I thought you had the Tamon Design one but that looks like the old Racing Beat...

Bodywork looks perfect BTW and you can't rush perfection, right?