Buildup: 91 Vert, A-spec 500R + lots more.
#1210
Saiga-12 Power!
Thread Starter
iTrader: (4)
Join Date: Oct 2004
Location: N of Chicago
Posts: 4,384
Likes: 0
Received 0 Likes
on
0 Posts
Your sarcasm detector needs a recalibration, sir!
Don't have any recent pics. I do have one with the IC piping complete. Maaaaybe I'll post that later tonight. I think my couplerless setup will give some folks some mega-wood.
Last edited by Juiceh; 03-25-10 at 06:12 PM.
#1214
My Bick is Digger
iTrader: (3)
seriously though I feel like an *** now. I heard Juiceh was done with this car and was just holding out on giving us finished pics. I heard he was driving the car all over the place.
Seriously dragging us through years of a thread to see our wet dreams all come true and not show it finished would be fucked up. But since you still aren't done then I feel the *** for hassling you.
Seriously dragging us through years of a thread to see our wet dreams all come true and not show it finished would be fucked up. But since you still aren't done then I feel the *** for hassling you.
#1215
RX-347
iTrader: (2)
There is an excessive amount of male *** in the past few posts. Little disturbing.
I'd definitely like to see some pics. I don't love EVERYTHING done, but I like a lot of the innovative little ideas used, and it's definitely a quality build. Looking forward to seeing what else you've come up with.
I'd definitely like to see some pics. I don't love EVERYTHING done, but I like a lot of the innovative little ideas used, and it's definitely a quality build. Looking forward to seeing what else you've come up with.
#1216
Saiga-12 Power!
Thread Starter
iTrader: (4)
Join Date: Oct 2004
Location: N of Chicago
Posts: 4,384
Likes: 0
Received 0 Likes
on
0 Posts
Should flow nicely!
Couple things being redone at the moment. The coolant neck is being redone with one piece to match the IC piping curves and give a cleaner look. The turbo is also being changed. Sean says my current 500R turbo makes me "Happy", but the change will make me "Very Happy!"
You like it and you know it!
#1218
Saiga-12 Power!
Thread Starter
iTrader: (4)
Join Date: Oct 2004
Location: N of Chicago
Posts: 4,384
Likes: 0
Received 0 Likes
on
0 Posts
Was my iPhone camera. Didn't have my good camera with me at the time. The lighting was also sucky. That was a flashlight on the engine bay.
I don't recall how far it drops down. I'll take some measurements when I can. I think its like a 2-3 inch drop.
I don't recall how far it drops down. I'll take some measurements when I can. I think its like a 2-3 inch drop.
Last edited by Juiceh; 03-26-10 at 03:10 PM.
#1223
Saiga-12 Power!
Thread Starter
iTrader: (4)
Join Date: Oct 2004
Location: N of Chicago
Posts: 4,384
Likes: 0
Received 0 Likes
on
0 Posts
Nope. Hot side has the same clamp. They are Hargett Precision Quick Disconnect Clamps. Sean knows a guy that uses these on his tractor pull rig at ~150-200psi, no problems.
They will be eventually. I want to hard coat anodize the cold side & intercooler black(enhances heat dissipation) then ceramic coat the cold side black(reject heat from getting back in). Sean told me not to anodize the comp housing and the attached piping though since the comp housing is cast and cast AL tends to turn out like *** when anodized. So that bit will probably be ceramic coated to look nicer. Anodizers around here are kinda **** about what they will anodize. They all complain about not having enough work to do, yet when you take them something simple like say AL wheel center caps to anodize they will turn you away. Very bizarre... Haven't taken my IC to an anodizer yet though but that is what I've been told about multiple anodizers in the area.
Yup, piping is welded to the greddy comp tube.
They will be eventually. I want to hard coat anodize the cold side & intercooler black(enhances heat dissipation) then ceramic coat the cold side black(reject heat from getting back in). Sean told me not to anodize the comp housing and the attached piping though since the comp housing is cast and cast AL tends to turn out like *** when anodized. So that bit will probably be ceramic coated to look nicer. Anodizers around here are kinda **** about what they will anodize. They all complain about not having enough work to do, yet when you take them something simple like say AL wheel center caps to anodize they will turn you away. Very bizarre... Haven't taken my IC to an anodizer yet though but that is what I've been told about multiple anodizers in the area.
Yup, piping is welded to the greddy comp tube.
Last edited by Juiceh; 03-27-10 at 04:45 PM.