T56 Trans install
10-21-05, 08:38 PM
#1
8.12 @18psi
Thread Starter
Join Date: Oct 2003
Location: philly
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
T56 Trans install
here are pics of a t56 trans g force made. only thing you have to modify is the shifter location like 3 inches forward every thing else is like a charm. you have to use a hydrolic throw out bearing with this setup. the bell housing is from a chevy modified for stock starter position. also includes a midplate when you buy everything.
10-21-05, 09:19 PM
#6
Living life 9 seconds at a time
iTrader: (2)
Join Date: Feb 2001
Location: Abingdon, Md
Posts: 6,541
Likes: 0
Received 0 Likes
on
0 Posts
I sold it because I was afraid of what happened to Demetrios's car could happen to me. The injector setup is screwed down in the casting of the manifold which pulled right up and out of the threads causing his car to burn to the ground last year. If you helicoil the brackets to the manifold, I suppose it would be safer. Be careful. Its a nice setup, but should be designed a bit differently with a plenum. Im getting a custom one made this winter. I'll post pic's of it when its done with flow bench results. It'll be for sale from PFSupercars.
10-21-05, 09:28 PM
#7
8.12 @18psi
Thread Starter
Join Date: Oct 2003
Location: philly
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
o ok thanks. im going to modify it by putting bigger studs and weld it through the inside so that it wouldn't rip the treads right out and keep its strenth. remember its only a stupid 11 wrench bolt holding it down . i was afraid the other day i turned it to hard and felt it turn alittle more. so now it definately has to be modifyed.
Trending Topics
01-05-07, 01:39 PM
#8
MenWithGutsAttackCorners!
Join Date: Nov 2006
Location: bristol tn
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jdmluver
why did you get rid of the jay tech manifold set up ernie. i dont like the lower intake manifold (the way they make them) but i like the top portion.
01-05-07, 01:50 PM
#9
Originally Posted by vtakk eg
where can you get that setup? the one in the last pic posted in the tread ? and how much is it?
jdmluver, would you be so kind as to list all of the parts you needed for the install?
01-05-07, 11:13 PM
#12
Killer
Join Date: Oct 2003
Location: Philadelphia
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
im using a hydrolic throw out bearing, the flywheel is a mcleod dual disc (same diameter as stock. the input shaft was made when i ordered the trans from g-force transmissions.
01-06-07, 01:11 PM
#14
Originally Posted by jdmrxluver
im using a hydrolic throw out bearing, the flywheel is a mcleod dual disc (same diameter as stock. the input shaft was made when i ordered the trans from g-force transmissions.
01-06-07, 07:39 PM
#15
Killer
Join Date: Oct 2003
Location: Philadelphia
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
I bought the throw out bearing and the clutch setup from mcleod clutches so its custom from them. The clutch setup was made to the exact dimensions of the stock flywheel, it works fine for the street also. On the trans i havn't tested the car on the road yet but g-force says it shouldn't be loud on the street because its not a dog ring trans.
Thread
Thread Starter
Forum
Replies
Last Post
82streetracer
1st Generation Specific (1979-1985)
7
08-23-15 09:28 AM
