Sexiest video ever! Just set my GT35R on my block
#1
Sexiest video ever! Just set my GT35R on my block
Hey guys. I have to share this one. I just placed my GT35R and my entire fuel system on my block for sizing and it was too sexy to ignore. It's a GT35R T4 housing from A-Spec. The secondaries are 1680cc and I wired the resistors to the harness on the cabin side of it. Enjoy the vid as much as I do.
http://www.youtube.com/watch?v=EZBzKYBhU5I
http://www.youtube.com/watch?v=EZBzKYBhU5I
Trending Topics
#9
Unhealthy Obsession
iTrader: (3)
Join Date: May 2006
Location: NNJ
Posts: 482
Likes: 0
Received 0 Likes
on
0 Posts
+ on the ID2000s.
I hope that Fpr is actually a legitimate brand. Dont be unsure and run a knock off Fpr.
You have a good thing going with these organized/informative videos. Keep it up.
I hope that Fpr is actually a legitimate brand. Dont be unsure and run a knock off Fpr.
You have a good thing going with these organized/informative videos. Keep it up.
#16
Mad Man
iTrader: (5)
And when do you think he will see low enough pulsewidths on secondaries to need the ID2000's? Shoot the latency itself will get you past the non linearity of the 1600. Staging usually doesn't use those low of opening values. If he was going to idle with 1600's it might be a good idea but not as secondaries.
#17
Rotary Freak
iTrader: (4)
Join Date: Aug 2005
Location: US
Posts: 2,150
Likes: 0
Received 0 Likes
on
0 Posts
rdhma, I just wanted to say that I've watched a few of your videos and they are a lot of help on explaining some of the systems within the RX7. I am actually in the middle of pulling my engine myself and it looks like we have the exact same cars haha. I have a A-Spec 500R and will be getting the motor rebuilt with 3mm seals and all. You're a few steps ahead of me seeing that the engine is already out of your car, I'm still working on it
This is my build thread if you'd like to follow along! Good luck with the rest of your build.
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/starting-off-new-year-engine-pull-880500/
This is my build thread if you'd like to follow along! Good luck with the rest of your build.
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/starting-off-new-year-engine-pull-880500/
#19
rdhma, I just wanted to say that I've watched a few of your videos and they are a lot of help on explaining some of the systems within the RX7. I am actually in the middle of pulling my engine myself and it looks like we have the exact same cars haha. I have a A-Spec 500R and will be getting the motor rebuilt with 3mm seals and all. You're a few steps ahead of me seeing that the engine is already out of your car, I'm still working on it
This is my build thread if you'd like to follow along! Good luck with the rest of your build.
https://www.rx7club.com/showthread.php?t=880500
This is my build thread if you'd like to follow along! Good luck with the rest of your build.
https://www.rx7club.com/showthread.php?t=880500
#20
Stay tuned...
iTrader: (3)
Join Date: Jul 1997
Location: West Islip, Long Island NY
Posts: 2,917
Likes: 0
Received 1 Like
on
1 Post
Are you using them?
Are you using them?
Are you speaking from experience?
I agree, I was thinking of swapping my two 1680cc primaries for two 1000 ID injectors but for the same reason you mentioned keeping the four 1680 cc secondaries.
I'd really like to hear from those using the ID injectors, either way I am going to order a set soon and will post the results.
Thanks,
Anthony
Are you using them?
Are you speaking from experience?
And when do you think he will see low enough pulsewidths on secondaries to need the ID2000's? Shoot the latency itself will get you past the non linearity of the 1600. Staging usually doesn't use those low of opening values. If he was going to idle with 1600's it might be a good idea but not as secondaries.
I'd really like to hear from those using the ID injectors, either way I am going to order a set soon and will post the results.
Thanks,
Anthony
#24
rotorhead
iTrader: (3)
Are you speaking from experience?
Since most people are using the PFC with the factory saturated injector drivers and some resistor, what are they going to use for the 3 injector overlap settings, the pri/sec transition % and Sec transition msec settings? How about lag settings? On the various 1600/1680 cc injectors out there, there are bunch of well documented settings to try for these. Whereas with the 2000cc injectors, you're reinventing the wheel or shoehorning in some other settings and hoping the car runs right.
Unless the setup really would require 2000cc injectors, you are just creating a bunch of work for yourself trying to get the staging right in order to eliminate lean or rich spots. It's one thing to try them for a personal experiment, but it's another to give someone advice of "oh put 2000cc injectors in, they're like 1600's but better." Rarely is one part hands-down 100% better versus another, there are tradeoffs to everything. Bigger injectors have more lag for example, although it can depend on the injector design (bigger low impedence injector can be more responsive than small high impedence injector).
You could say "oh, x tuner is going to take care of the staging." Well x tuner is running a business and doesn't see 2000cc injectors every day so he has no incentive to spend time testing. It's just a pointless purchase for somebody who just wants to drive their car and not fiddle with the tune all time.
#25
Senior Member
iTrader: (4)
I am not, however I have been in a few cars with them, and there is zero transition problems with the ID injectors;
Here is one for example;
https://www.rx7club.com/single-turbo-rx-7s-23/twin-to4e-fd-setup-880676/
Here is one for example;
https://www.rx7club.com/single-turbo-rx-7s-23/twin-to4e-fd-setup-880676/
Are you using them?
Are you using them?
Are you speaking from experience?
I agree, I was thinking of swapping my two 1680cc primaries for two 1000 ID injectors but for the same reason you mentioned keeping the four 1680 cc secondaries.
I'd really like to hear from those using the ID injectors, either way I am going to order a set soon and will post the results.
Thanks,
Anthony
Are you using them?
Are you speaking from experience?
I agree, I was thinking of swapping my two 1680cc primaries for two 1000 ID injectors but for the same reason you mentioned keeping the four 1680 cc secondaries.
I'd really like to hear from those using the ID injectors, either way I am going to order a set soon and will post the results.
Thanks,
Anthony