Innovate HELP
#1
MY78U
Thread Starter
Join Date: Sep 2005
Location: Nashville TN
Posts: 261
Likes: 0
Received 0 Likes
on
0 Posts
Innovate HELP
I am just starting the install on the Innovate lc-1 and xd-1 but I am not really sure on somethings.
1. If I am just using the xd-1 for a read out on my a/f do I need to use the calibration wire?
2.Can I use the heater and the system ground in the same place?
3. What is the heater ground do ?
4. Where do you guys recoment on grounding the wire?
5. The system ground is for another hook up right? So I really dont need to ground it since i am runing the xd-1. correct?
6. What does the calibration wire do?
7. After installing it how do you do a calibration with a xd-1?
1. If I am just using the xd-1 for a read out on my a/f do I need to use the calibration wire?
2.Can I use the heater and the system ground in the same place?
3. What is the heater ground do ?
4. Where do you guys recoment on grounding the wire?
5. The system ground is for another hook up right? So I really dont need to ground it since i am runing the xd-1. correct?
6. What does the calibration wire do?
7. After installing it how do you do a calibration with a xd-1?
#3
Slower Traffic Keep Right
iTrader: (5)
This thread should answer most of your questions.
https://www.rx7club.com/power-fc-forum-47/inovative-wideband-o2-441157/
At least towards the end of it.
https://www.rx7club.com/power-fc-forum-47/inovative-wideband-o2-441157/
At least towards the end of it.
#4
Eats, Sleeps, Dreams Rotary
iTrader: (19)
Originally Posted by Thomas1277
I am just starting the install on the Innovate lc-1 and xd-1 but I am not really sure on somethings.
1. If I am just using the xd-1 for a read out on my a/f do I need to use the calibration wire?
2.Can I use the heater and the system ground in the same place?
3. What is the heater ground do ?
4. Where do you guys recoment on grounding the wire?
5. The system ground is for another hook up right? So I really dont need to ground it since i am runing the xd-1. correct?
6. What does the calibration wire do?
7. After installing it how do you do a calibration with a xd-1?
1. If I am just using the xd-1 for a read out on my a/f do I need to use the calibration wire?
2.Can I use the heater and the system ground in the same place?
3. What is the heater ground do ?
4. Where do you guys recoment on grounding the wire?
5. The system ground is for another hook up right? So I really dont need to ground it since i am runing the xd-1. correct?
6. What does the calibration wire do?
7. After installing it how do you do a calibration with a xd-1?
2.) not recommended
3.) ground the heater for your LC-1 sensor?
4.) the heater ground should go to a chassis ground and the system ground should go to where you will use the analog out signals.
5.)see 2
6.) See 1
7.) you should have calibrated it before you installed it. if you did not, then you messed up. if you did not and are asking about initial calibration then read the instruction becasue its way to long to type out.
#5
MY78U
Thread Starter
Join Date: Sep 2005
Location: Nashville TN
Posts: 261
Likes: 0
Received 0 Likes
on
0 Posts
I just found out that the kit was suppose to come with a Standalone widband kit instructions that i never got in my kit. The only thing I got was a cd that has directions for the lc-1 . Just want to say thanks for the help from everone.
Thread
Thread Starter
Forum
Replies
Last Post
Adaptronic MTX-L to adaptronic question
TeamRuffRacing
Adaptronic Engine Mgmt - AUS
1
09-30-15 08:13 PM