Can a bad catalytic converter do harm to the turbos and motor?
#1
Full Member
Thread Starter
Join Date: May 2002
Location: Cloverdale Bc
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Can a bad catalytic converter do harm to the turbos and motor?
I just put back my Catalytic Converter on my car, for emission purposes, I was told that the cat was cracking inside and that its almost heading south, anyhow I have it on and I have a downpipe in place to replace the precat and I have an aftermarket exhaust. I just got my turbos rebuilt and have a new motor with about 45000K on it. Should I keep the main cat in? atleast now I dont see spikes!!!!!! and does a bad main cat pose a threat to the new turbos and motor? I will be getting a ecu and an intake for my car in a couple of weeks
#3
Braap Braap Braap BOOM!
Join Date: Mar 2001
Location: Ft. Worth, TX
Posts: 843
Likes: 0
Received 0 Likes
on
0 Posts
A clogged cat will cause too much backpressure and will cause your motor and turbos to get too hot. You shouldn't drive around with it like that for too long.
#7
It doesn't sound like your main cat is clogged. If it's just cracked inside, you'll probably get a lot of rattle noise. The broken pieces inside could clog your cat and restrict flow so I wouldn't just ignore it completely. You can always put the MP back on and take care of the spike.
Trending Topics
#8
Braap Braap Braap BOOM!
Join Date: Mar 2001
Location: Ft. Worth, TX
Posts: 843
Likes: 0
Received 0 Likes
on
0 Posts
What happens is all the little honeycomb pieces break apart and lay loose inside the cat. When you get on it the exhaust pushes all of them back against the rear of the cat clogging the opening. Boost spikes are hard to control. Porting the wastegate and a good boost controller are needed.
#9
Rotary Enthusiast
Join Date: Mar 2001
Location: Mechanicsburg, PA USA
Posts: 1,392
Likes: 0
Received 0 Likes
on
0 Posts
A hi-flo cat is a happy medium between the stock cat and MP - gives you about 10-15 rwhp over stock and more overall power throughout the powerband - plus it weighs about 25-30 lbs less - keeps you legal and helps with boost spikes over a MP. A clogged stock cat can really cause a lot of heat that could damage the turbos and engine if not addressed soon.
#10
Rotary Freak
Originally posted by kwikrx7
A hi-flo cat is a happy medium between the stock cat and MP - gives you about 10-15 rwhp over stock and more overall power throughout the powerband - plus it weighs about 25-30 lbs less - keeps you legal and helps with boost spikes over a MP. A clogged stock cat can really cause a lot of heat that could damage the turbos and engine if not addressed soon.
A hi-flo cat is a happy medium between the stock cat and MP - gives you about 10-15 rwhp over stock and more overall power throughout the powerband - plus it weighs about 25-30 lbs less - keeps you legal and helps with boost spikes over a MP. A clogged stock cat can really cause a lot of heat that could damage the turbos and engine if not addressed soon.
I just installed an N-tech Hi-flow cat and the sucker flows TOO well! Before I installed it I was able to control the boost just fine with needle valves. Since the N-tech went in I'm getting crazy spikes. Even with 2 restrictor plates w/ 2" openings before and after the cat I still get boost creep. Porting the wastegate is gonna cost $600. Ouch!
#11
Out of order
iTrader: (5)
Join Date: Nov 2001
Location: somewhere
Posts: 7,040
Likes: 0
Received 0 Likes
on
0 Posts
Not to sound ignorant, but i was always curious, isnt getting an aftermarket wastegate cheaper? I mean, i know the FD with hard inter. pipes have em, but whats the main reason for porting the wastegates, as opposed to getting per say, an HKS wastegate or something?
thanx ahead of time.
thanx ahead of time.
Thread
Thread Starter
Forum
Replies
Last Post