ahh help.. weird problem
#1
Rotary Enthusiast
Thread Starter
ahh help.. weird problem
Well, I took off my manifold , polished it , removed my cruise control, and threw my car back together. It was fine in the beginning allthought he vacuum went down from 16-17 to 14-16. Started driving it around a little bit, and noticed that sometimes in first I would be giving it a certain amount of throttle and the car would buckle every so often at any given rpms below 3000. Now tonight, Its been running fine, no problems, and on the way home from my girls house my vacuum dropped to 12-13.
It still pulls just as hard, enough that I kept up with afew crotch rockets tonight.
The problem is, is if I give it some gas, or I have been driving and come to a stop and push the clutch in, the idle stumbles and drops to like 400-500 rpms and stays there till I give it some gas.
If im just sitting in place and I rev it, it revs up, then I hear this light clanking noise and it gets to like 4-500 rpms and almost dies.
IS my motor on its way out?
I do have almost 84 k on it.
I replaced my MAP sensor vacuum line just a min ago, fired her up again, and it idles with the driving lights on at about 700-750 rpms pulling 14 to 15 mercury in vacuum, but still has that weird stumbeling problem.
Whats going on???
Steve.
Mods below
It still pulls just as hard, enough that I kept up with afew crotch rockets tonight.
The problem is, is if I give it some gas, or I have been driving and come to a stop and push the clutch in, the idle stumbles and drops to like 400-500 rpms and stays there till I give it some gas.
If im just sitting in place and I rev it, it revs up, then I hear this light clanking noise and it gets to like 4-500 rpms and almost dies.
IS my motor on its way out?
I do have almost 84 k on it.
I replaced my MAP sensor vacuum line just a min ago, fired her up again, and it idles with the driving lights on at about 700-750 rpms pulling 14 to 15 mercury in vacuum, but still has that weird stumbeling problem.
Whats going on???
Steve.
Mods below
#3
Dont like it? I dont care
Join Date: Jan 2003
Location: Gold's Gym
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Kinda sounds like a vacuum leak. You sure you got everything back together right? When you took your manifold off I assume you meant the intake manifold? Are you sure you've got everything sealed off right? Sure nothing accidentally came undone? Search around in there a little bit and see what you find.
#4
Rotary Enthusiast
Thread Starter
Thats what I thought too... I did brake one of the studs holding on the intercooler elbow, think its causing any problems? But then I Thought a LEAK would cause a higher idle, and I would loose boost too.
And I just went outside took it for a spin again, and its running perfect again -15 to -16 at 8-850 rpms
And I just went outside took it for a spin again, and its running perfect again -15 to -16 at 8-850 rpms
#5
Dont like it? I dont care
Join Date: Jan 2003
Location: Gold's Gym
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Rx-7$4$me
Thats what I thought too... I did brake one of the studs holding on the intercooler elbow, think its causing any problems? But then I Thought a LEAK would cause a higher idle, and I would loose boost too.
And I just went outside took it for a spin again, and its running perfect again -15 to -16 at 8-850 rpms
Thats what I thought too... I did brake one of the studs holding on the intercooler elbow, think its causing any problems? But then I Thought a LEAK would cause a higher idle, and I would loose boost too.
And I just went outside took it for a spin again, and its running perfect again -15 to -16 at 8-850 rpms
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
The1Sun
1st Generation Specific (1979-1985)
7
09-18-15 07:13 PM