damian

iTrader: (2)

i dont think it matters UNLESS the restriction is built in to the nipple outlets there, supposedly the later cars have the restriction there and no pills...mine is a 95 and it had pills, so I can't confirm that.... but your right, it should not matter. both of those nipoples see the same pressure

damian

iTrader: (2)

by the way, i though i would upadate where I am on this thread, I installed a power FC a few days ago so I went back to the stock solenoid boost controll setup to test the boost control of the PFC.... then after dooing a pressure test on the 2ndary I noticed it was NOT getting pre-spooled so after I debug that I will see if it fixes the 10-5-10 pattern I am seeing with the PFC.

bureau_c

Here's an update for those of you who were looking at a slightly cheaper way to do Damian's setup. I'm using the JoeP XZ controller with a non-standard lighter spring provided by Joe himself (his web site is at

http://www.joepmbc.com/

and he is a former FD owner). His controllers, while not quite as pretty as the Hallmans, seem to be constructed very well, require no tools to adjust (if you get the newest, the XZ) and I would imagine he will make the lighter spring an available option.

I don't think the spring is quite as light as the Hallman that Damian used, which was why my setup wasn't working when connected as he originally had it. I believe the additional volume required to fill up the lines aft of the wastegate/precontrol actuators allowed the boost to build higher than I wanted it even with the MBC adjusted to the lowest setting. However, when I capped off the wastegate actuator vent the lowest setting gives me a nice friendly 8 psi. I now have to reconnect the precontrol MBC because I didn't figure this out until I had already taken it out of the loop :-(

I'll post more when I have it, but so far this looks like a nice alternative implementation for about 1/2 the price.

Once again I'd like to thank Damian for starting this thread and helping out with good advice, and Joe P for working with me on the alternate spring. And no thanks to Mazda for making those damned lines and nipples so hard to reach! :-)

jds

Razerx

Ok, just so i am on the same page, when you talk abou the pills. you are talking about the stock brass 'beads' that are inside the lines, as opposed to plasic ones that are in-line, such as by the intake/solinoids.

bureau_c

I actually am not sure what "in-line" plastic things you're referring to, but yes...these are the flow restricting things inside the lines leading from the turbos to the inlet side of the wastegate and precontrol actuators....unless you have the '95 turbos (well, SOME of the '95 turbos) which have the restriction built into the nipples on the turbos.

jds

damian

iTrader: (2)

great info bureau_c....

Razerx

so when you look for the boost pattern should you be 4th or 5th gear, so you have more time to notice, because my sweeps so fast in the first few gears.

Razerx

So when you are looking for the boost pattern, which gear do you recommend?

bureau_c

I usually do my testing in 2nd and 3rd gear. I don't have any room around here where I can do many 4th gear runs up to redline!

jds

rajeevx7

iTrader: (11)

does this setup mean connecting the two second nipples of the actuators together via a hose?

bureau_c

Assuming by "second nipples" you mean the vent side of the wastegate and precontrol actuators, don't connect them together, just cap them off.

jds

rajeevx7

iTrader: (11)

alright, i figured it out.

connect lines from actuators to where the outlet hoses from the electrical solenoids are connected, thus bypassing the solenoids...ohhhh

thanks, raj

rajeevx7

iTrader: (11)

alright, i figured it out.

connect lines from actuators to where the outlet hoses from the electrical solenoids are connected, thus bypassing the solenoids...ohhhh

thanks, raj

bureau_c

Well, using JoeP controller valves, connecting the actuator vents as originally suggested did NOT work for me. It seemed to work for Damian. I set mine up as he later set up his, by capping the actuator vents...just like most electronic boost controller solenoids are set up. The more I think about it, the better this method seems. All the extra volume aft of the actuator is bound to affect the response of the wastegate and precontrol, which is exactly what I saw. I couldn't turn the boost down far enough to avoid huge spikes. Once I capped the actuator vents it worked much better...no spiking and I actually have some room to work with between about 7 psi and the stock 10 (I'm not going higher than that right now since my Pettit ECU gave up the ghost and I'm back with a stock ECU temporarily).

jds

damian

iTrader: (2)

interesting info jds, agreed, the setup with the capped ends is probably better, the previous setup i did was simply to try and maintain the stock flow paths, but i realized it was not that important.