Where 2 bolt 4 point harness
#1
Junior Member
Thread Starter
Join Date: Oct 2002
Location: espanola, new mexico
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
Where 2 bolt 4 point harness
I have a question, I just bought a set of 4 point harnesses for my racing seats, but i don'y know were to bolt on the top part of the harnesses. I don't have a rear strut tower bar. Any one know were to bolt em.
#2
omae mo na!
Join Date: Nov 2004
Location: NEW JERSEY
Posts: 861
Likes: 0
Received 0 Likes
on
0 Posts
oh sweet jesus why would you bolt them to your strut tower bar?!?!?!
your supposed to attach them to your rollcage.
search on that, there was a GREAT write-up a few weeks ago about 4-points and rollcages.
your supposed to attach them to your rollcage.
search on that, there was a GREAT write-up a few weeks ago about 4-points and rollcages.
#4
as a SAFTEY hazard do not bolt them under your seat or below like 23* or something, in a collision with this low mounting position, your spine could be compressed and easily break.
#5
Army Strong...or somethin
iTrader: (3)
Join Date: Jan 2004
Location: Green Bay, WI
Posts: 857
Likes: 0
Received 0 Likes
on
0 Posts
yeah, u are advised to keep them level or on a downward angle so that u dont compress ur spine!!
also u are sposed to mount them on the roll cage, wither that or but/maie a harness bar
u can make one pretty easy, just get a pipe (a strong one!!) and weld on some steel stock to the ends as brackets (after u measure it up and cutting it a little short to compensate for the brackets) and then weld it onto the b-pillars and ur set! i wouldnt have the welder too hot though or it may show up on the outside of the car lol
and as stated before, keep the harness bar above the opening for the harnesses!!
also u are sposed to mount them on the roll cage, wither that or but/maie a harness bar
u can make one pretty easy, just get a pipe (a strong one!!) and weld on some steel stock to the ends as brackets (after u measure it up and cutting it a little short to compensate for the brackets) and then weld it onto the b-pillars and ur set! i wouldnt have the welder too hot though or it may show up on the outside of the car lol
and as stated before, keep the harness bar above the opening for the harnesses!!
#6
Like Ghandi with a gun
Join Date: Mar 2003
Location: Rapid City, SD
Posts: 4,584
Likes: 0
Received 0 Likes
on
0 Posts
Lol... you bolt them to the ceiling bar on your ROLL CAGE, wich apparently you don't have... A small roll cage would cost about $300 shipped, or go to your local machinist and he'll bend one out for probably around $200 that will work. You took the cash to buy racing seats and harnesses... finish it out right...
#7
Nurse I need 1300cc's NOW
i mounted mine to where the stock seat belt mounting points are,, since my electric ones didnt work i ripped them out and replaced them with the 4 point harness (probobly get flammed but thats what i did. and so far its worked well for me
Trending Topics
#9
I live in an igloo
Join Date: Jul 2004
Location: calgary alberta
Posts: 2,546
Likes: 0
Received 0 Likes
on
0 Posts
Sparco makes a harness bar that bolts in to your standard seat belt bolts and then down by the seats. Its approved im pretty sure by some safety company, you may want to check that out on their site. They also have a list of dealers and I suggest you call them on pricing and fitment for the FC. Im guessing around 300-400$ USD.
#10
Army Strong...or somethin
iTrader: (3)
Join Date: Jan 2004
Location: Green Bay, WI
Posts: 857
Likes: 0
Received 0 Likes
on
0 Posts
this place sells cheap CERTIFIED cages!!!
http://www.swracecars.com/
160 for an 8 point for the FC if i remember correctly!!
this is where i will be getting my cage from!! my buddy got one for his FD and another buddy for his SC300!
http://www.swracecars.com/
160 for an 8 point for the FC if i remember correctly!!
this is where i will be getting my cage from!! my buddy got one for his FD and another buddy for his SC300!
#12
Like Ghandi with a gun
Join Date: Mar 2003
Location: Rapid City, SD
Posts: 4,584
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Bigretardhead
I don't see anything on that page about a roll bar or cage of any sort...
#13
Rotary Freak
Join Date: Apr 2002
Location: Boulder, CO
Posts: 1,739
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Kenteth
did you even bother to look...? seriously. Took me less then ten seconds to find the roll bars and ive never even been on their site.