Icemark

Okay I finally broke down and spent the money on structual foam to stiffen my 88 vert's frame.

For those not familier I used ITW Foamseal's AUTOSEAL. (http://www.itwfoamseal.com/auto_aftermarket.htm).

ITW Foamseal's AUTOSEAL is a two component foam kit that has been specially formulated for automotive aftermarket applications such as chassis stiffness improvement, sound damping, and reduction of vibration and infiltration of air, water and dust.

But my main concern was stiffening the FC3C body further than Mazda did; while not adding significant weight.

So, Saturday afternoon I am playing around with the stuff and filling the drivers running boards, and unibody cavities. Takes about two kits for each side of a vert, filling the metal under the running boards and the entire unibody framing.

Now normally you fill cover all the holes after squirting the stuff in and let it go to town. Just like that cheapo crap at home depot if fills to about 5 -10 times its size.

Well, after letting the car sit all Saturday afternoon, and night on a perfectly level surface, I check it out. Sure enough it has filled perfectly under the tape and plugs, and is ozzing slightly exactly how it should, but now fairly solid everywhere I can check it.

So I figure the stuff has solidified and back the car out into my driveway, so I can take advantage of the sun and clean the carpets (with 3M carpet and Upholstry cleaner of course)... clean the carpets since the plastic running boards off, from when I injected the stuff into the panels.

I let it sit all day in the sun drying and thinking nothing of it.

So this morning I go to open the drivers door. It unlocks but sounds a little weird (I have added a keyless security system on to the stock system). I go to open the door and it will not open... it doesn't move. Latch pulls up, but door does not open.

"Great, the damm latch is broken at the actual mechanical latch in the door jam", I think cursing. I know this is a common thing on older Japanese cars, but I still am bummed. I could have spent the money for parts replacing the damm latch instead of foaming the panels.

I go inside from the passengers side, and the interior latch is not opening it either... How to take the interior door panel off without opening the door starts coming to mind... "well, I can get to all but that one screw from inside, I guess I can bust the screw"...

Then something dawns on me... maybe that foam wasn't done expanding 24 hours afterwards...so I climb back out, and try the drivers door from outside again... this time I can just open it a hair... enough to get my fingers in around where the top of the door meets the body of the vert.

I start pulling with one hand while holding the handle up with the other.. I am hearing something ripping. Now mind you I am pulling with all my force... and I am a big guy... 6'2" 225 lbs, can easy lift a bare block 13B out of my truck, and carry it to the garage.

Finally the door rips open... I look down...

There between the sandwhich of sheet metal that makes up the FC3C framing at the running boards, a small (tiny really) 1/8 bead of the foam has expanded its way up through the sandwhich, and literally expoxied the door to the frame.

I should have probably taped even the sandwich of the body framing up.

Looking at the bottom of the door there is foam stuck all over the lower gasket and door jam...

Well at least I know that stuff works.

jhammons01

I used to work with that stuff back in the 80s. It usually is dry and flakes off if you rub. BUT sometimes if the resin was'nt mixed properly it would be gummy and wouldn't flake at all!!! Did yours flake or is it gummy???? Did it stick to the paint??? I remember we used to use methyl ethyl Ketone (spelling is bad) to disolve the stuff but it is now illegal in most states. You could try Isopropal Alcohol. Fingernail polish will disolve it but will also get your paint. MEK will also work on your paint so be careful if you find some. Also try good ole 89 octane

drcoopster

Ouch. Sounds like it certainly works though.

Icemark

Different foam stuff... MEK doesn't touch this stuff (I have about 3 gallons left from a 5 gallon of MEK I bought back inthe 80's). I dropped a hunk of this structual foam into a cup of MEK and it just floated.

It didn't get either flaky or gummy once dry, but rather a very very hard light weight plastic.

Acetone seems to work just fine though... just have to be careful with the paint and plastic, not to run too much.

Dltreezan

iTrader: (3)

yeah this is the two part urethane foam it sounds like. Isnt it about the same.....two part and when you mix it it turns into this mocha color?

Dltreezan

iTrader: (3)

but since we are on the subject how do you like the sound deadener and stiffness of the frame and whatnot?

RotaryResurrection

iTrader: (8)

pics?

Madrx7racer

pics please? I cannot picture what you did.....sorry

RETed

Two part urethane foam will not dissolve under most solvents and chemicals.
Even MEK (methyl ethyl ketone [you got the spelling right ]) nor acetone will dissolve it.
If you have unmixed sections, it might come off with some of the stronger cleaners (like acetone).

Watch out with the particles of the set foam when you're trying to cut or shave pieces off.
If this stuff gets into your skin, it's a major irritant!


-Ted

Dltreezan

iTrader: (3)

yeah I have the stuff on the carpet in my car....needless to say it isnt going anywhere until i get new carpet.

fcfdfan

Ted,

What do you think of this chassis stiffening foam method? Is it worth it?

Thanks.

OverDriven

MEK isn't illegal...you can pick it up at Home Depot.

lgjp2631

next time something happens with that foam just put some gas on it.it will loosen right up.i use that foam alot.lol its a good filler when doing bondo.

KiyoKix

Icemark...where did you go, I wanna know how well this stuff works? I've thought about it before but I wasn't really sure if I wanted to do it yet, how do you feel about it? Got any pics of the car after it's done (any video so we can see the body move?). I'm very curious now .

Kiyo

Bukwild

Like I had stated before when someone on this forum did this. My dad had a Ferrari 355 F1 and this was done to the vert to stiffen up the chassis and it handled like no other car I ever rode it. I never got a chance to drive it because I was in the service while he owed it plus he would never have let me drive it because I would have seen what it could do. But riding in the passanger seat and hitting corners at 80 it felt like zero body roll.

Icemark

I haven't had a chance to drive the car yet, as yesterday I couldn;t get the door open, so I just took my truck.

I'll try it later today.

And Ted's right... this stuff does not disolve in acetone either once it is dry and hard.

Again here is the link for what I used:
http://www.itwfoamseal.com/auto_aftermarket.htm

And yes MEK is illegal in most states. Only a very few allow it still to be sold.

barcode

iTrader: (1)

You can get it out of your skin fairly easily with an old wool sweater. That trick also works like a champ when you're working with fiberglass.

vectorminds

where is it that you are injecting the foam? (pic with arrows maybe )

Icemark

Yeah I didn't have too much of a problem with my skin.. as whenever I am working in the shop, I wear latex gloves, and even more so when painting or using adhesives (whihc this foam really is).

Icemark

Yeah let me see if I get some tomarrow... I have been so busy.

RETed

I was working on this stuff one night, shaving a bunch of stuff that fell on the ground.
I just sat in it with no protective gear.
I stuck to my pants.
I was too tired to remember to "dust" it all off.
I got into the car, and it got all over the seat.
I got into bed, and it got all over the bed.
It was NOT fun that morning!


-Ted

Icemark

Ah, yeah... that would do it... it would be next to impossible to get all the shavings out of a cloth seat...

Icemark

The blue arrows are where I shot foam in and taped over it, and the green arrow is were is came up and sealed the door shut until I busted it free.

Nick86

iTrader: (1)

Replace the "Foam" with the black tar inside the doors - and you have my story as well!


I'll be interested to hear how this effects the car's feel.

Is there any fear that this stuff would seal up any of the car's drainage paths for water? I realize most of them are "purpose built" like he ones in the rear hatch and for the sunroof - but if you got a bit more "aggressive" with the placement of the foam, is there a danger of trapping water when it rains?

ProjectRESuperG

Wow, interesting!

I would love to try that as well. Question: Wouldn't the foam bust open the fill holes with the tape over it?

Love to know how your car handles after the foam Icemark!