RX7Club.com - Mazda RX7 Forum

2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

Remove fuel pump q

Thread Tools
 
Search this Thread
 
Old Oct 4, 2008 | 10:05 AM
Share
  #1  
cmanns's Avatar
cmanns
Thread Starter
Smoke moar
Tenured Member 05 Years
 
Joined: Aug 2006
Posts: 2,530
Likes: 1
From: The yay, California
Remove fuel pump q
So to remove it unplug batt, unscrew pump and yank up?

Never removed a fuel pump before, yes I did search and the results are not helpful at all!
Reply
0
Old Oct 4, 2008 | 10:39 AM
Share
  #2  
SirCygnus's Avatar
SirCygnus
whats going on?
Tenured Member 20 Years
iTrader: (1)
 
Joined: Mar 2004
Posts: 4,930
Likes: 8
From: atlanta ga
its painless. just do it. i did it without even needing to look at anything.
Reply
0
Old Oct 4, 2008 | 10:40 AM
Share
  #3  
cmanns's Avatar
cmanns
Thread Starter
Smoke moar
Tenured Member 05 Years
 
Joined: Aug 2006
Posts: 2,530
Likes: 1
From: The yay, California
Originally Posted by SirCygnus
its painless. just do it. i did it without even needing to look at anything.
Well yeah but the tight area where I live, and I don't know if it just goes into the gas tank, imagin a spark lol thus I was thinking disable batt first :P
Reply
0
Old Oct 4, 2008 | 10:41 AM
Share
  #4  
Aaron Cake's Avatar
Aaron Cake
Engine, Not Motor
Tenured Member: 20 Years
iTrader: (1)
 
Joined: Feb 2001
Posts: 29,798
Likes: 128
From: London, Ontario, Canada
You'll see the the flange is held on my a bunch of Phillips screws. They may or may not be rusted to oblivion. Just disconnect the fuel lines and harness, remove the screws, and lift out the pump assembly.
Reply
0
Old Oct 4, 2008 | 10:58 AM
Share
  #5  
cmanns's Avatar
cmanns
Thread Starter
Smoke moar
Tenured Member 05 Years
 
Joined: Aug 2006
Posts: 2,530
Likes: 1
From: The yay, California
Originally Posted by Aaron Cake
You'll see the the flange is held on my a bunch of Phillips screws. They may or may not be rusted to oblivion. Just disconnect the fuel lines and harness, remove the screws, and lift out the pump assembly.
Got it, thanks =)
Last edited by cmanns; Oct 4, 2008 at 11:18 AM.
Reply
0
Old Oct 4, 2008 | 07:05 PM
Share
  #6  
dean23's Avatar
dean23
pwned
Tenured Member 05 Years
 
Joined: Sep 2005
Posts: 1,296
Likes: 0
From: Northern Indiana
i would plan on replacing them. i used stainless hex key bolts to replace them all.
Reply
0
Old Oct 4, 2008 | 07:07 PM
Share
  #7  
cmanns's Avatar
cmanns
Thread Starter
Smoke moar
Tenured Member 05 Years
 
Joined: Aug 2006
Posts: 2,530
Likes: 1
From: The yay, California
Nothings rusted on my car, the screws were perfect looking lol.
Reply
0
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Installed UIM gasket, now my engine won't run
trickster
2nd Generation Specific (1986-1992)
25
Jul 1, 2023 04:40 PM
Recommendations on a single E85 fuel pump for 600whp (13B-RE)
ChrisRX8PR
Single Turbo RX-7's
21
Oct 18, 2015 04:01 PM
1980 Anniversary Edition RX7 Conversion to TII 13B Journey - Draft
KAL797
Test Area 51
0
Aug 11, 2015 03:47 PM
Back to Subforum
2nd Generation Specific (1986-1992)
View Next Unread
New diff mount rear end still weird




Advanced Search

All times are GMT -5. The time now is 03:33 PM.