2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

re-started the rebuild motor today, BUT

Thread Tools
 
Search this Thread
 
Old 11-01-03, 04:39 PM
  #1  
Rotary Enthusiast

Thread Starter
iTrader: (77)
 
fong's Avatar
 
Join Date: Oct 2001
Location: Maryland
Posts: 1,197
Received 3 Likes on 2 Posts
re-started the rebuild motor today, BUT

the engine got rough run(I have to keep my feet on the gas petal), aslo, the car is running HOT HOT, when I kept it around 2300 rpm. I can hear the coolant in raditor is boiling. but why is that? I reused the previous themostat cuz the motor wasn't overheated, so I assume the themostat is a good one.)

I can think of anything else to check, besides the themostat. any clue?

thanks
Old 11-01-03, 05:10 PM
  #2  
...

 
Ryde _Or_Die's Avatar
 
Join Date: Aug 2001
Location: Tampa, FL
Posts: 7,539
Likes: 0
Received 0 Likes on 0 Posts
Overheating can only be caused by a few things. Is there enough coolant? Pull the t-stat out and either check it or get another one anyways. If coolant isn't leaking(which can be tested by a pressure test from a good shop for less than $50 usually) then it has to be blocked or the fan clutch could be bad.

I say ditch the t-stat first and see if it helps. Check for leaks yourself also. If it doesn't help then check the fan clutch.
Old 11-01-03, 10:31 PM
  #3  
Im a tall midget.
iTrader: (28)
 
Juan's Avatar
 
Join Date: Feb 2001
Location: So Cal, USA
Posts: 3,131
Likes: 0
Received 6 Likes on 5 Posts
Did you bleed the cooling system? Maybe you have air stuck in the system.
Old 11-03-03, 02:33 PM
  #4  
Rotary Enthusiast

Thread Starter
iTrader: (77)
 
fong's Avatar
 
Join Date: Oct 2001
Location: Maryland
Posts: 1,197
Received 3 Likes on 2 Posts
Originally posted by wan
Did you bleed the cooling system? Maybe you have air stuck in the system.
tried with another used themostat today, still running HOT. I saw the niddle was raising when I rev about 2000 rpm.

I think there might be some air in the cooling system. how can I burp those air out of the system?

thanks
Old 11-03-03, 02:36 PM
  #5  
Engine, Not Motor

iTrader: (1)
 
Aaron Cake's Avatar
 
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes on 91 Posts
There is a bleed screw at the top corner of the rad (passenger side). If this is not present, the best way I have found to bleed is to alternatively cover and uncover the coolant filler hole with your hand, while you pump the rad hose...Every few pumps, stop and top off coolant....Also, do a search for the "bubble test" to find out if engine is eating coolant.
Old 11-03-03, 03:53 PM
  #6  
Rotary Enthusiast

Thread Starter
iTrader: (77)
 
fong's Avatar
 
Join Date: Oct 2001
Location: Maryland
Posts: 1,197
Received 3 Likes on 2 Posts
Originally posted by Aaron Cake
There is a bleed screw at the top corner of the rad (passenger side). If this is not present, the best way I have found to bleed is to alternatively cover and uncover the coolant filler hole with your hand, while you pump the rad hose...Every few pumps, stop and top off coolant....Also, do a search for the "bubble test" to find out if engine is eating coolant.
thanks, but I don't see any white smoke. if coolant goes into engine, it will white smoke.

possible to leave the rad cap open, and have someone to fill the coolant when I rev the engine inside. I have been testing by myself.

will try again.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
incubuseva
2nd Generation Specific (1986-1992)
14
09-03-15 12:37 PM
sYnth.
Build Threads
0
08-19-15 06:27 PM
gtcd
1st Generation Specific (1979-1985)
30
08-19-15 02:44 AM



Quick Reply: re-started the rebuild motor today, BUT



All times are GMT -5. The time now is 03:55 AM.