nitrous pics
#1
Senior Member
Thread Starter
Join Date: Sep 2003
Location: vancouver, canada
Posts: 286
Likes: 0
Received 0 Likes
on
0 Posts
nitrous pics
im planning an extensive nitrous system for my S5 N/A. I was wondering if any of you with NO2 have pics of the controls (master switch, purging, button...etc.).
I dont know where to mount it with minimum interior modifications. i want the inside to look stock, tho the controls dont necessarily need to be hidden.
any pics or suggestions?
I dont know where to mount it with minimum interior modifications. i want the inside to look stock, tho the controls dont necessarily need to be hidden.
any pics or suggestions?
#2
Damn, I was hoping to *see* pictures of a nice nitrous setup.
I'd think the center console where the Security light & such are would be a good place to add controls. I have my fuel pump cut switch located there. I would suggest putting a flip-up cover on it though, passengers have an annoying tendency of asking "What's that?" as their fingers are hovering right over my fuel cut switch.
-=Russ=-
I'd think the center console where the Security light & such are would be a good place to add controls. I have my fuel pump cut switch located there. I would suggest putting a flip-up cover on it though, passengers have an annoying tendency of asking "What's that?" as their fingers are hovering right over my fuel cut switch.
-=Russ=-
#3
Rpm abuser
Join Date: Oct 2003
Location: New Port Richey, FL
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
after the rebuild im doing a pre-spool nitrous injection system. theres a kit i already bought on ebay thats pretty good. its got almost everything electircal u need minus the purge and other valves u need. im planting my switch probably under the arm rest. this way i cant accidently hit it. it only turns on when ur at full throttle 2 so even having the switch on, the wot switch wont be on unless u do it on purpouse say at a light or something. good luck
#4
Open up! Search Warrant!
Join Date: May 2002
Location: Kicking down doors in a neighborhood near you
Posts: 3,838
Likes: 0
Received 2 Likes
on
2 Posts
My panel is in the armrest. I took it out, drilled holes in the bottom for the wires to pass through, the ran the wires under the center console, off to the right side of the shifter (there's plenty of room so its not near the stick), and behind the passenger side panel where the passengers left leg would be, the part that surrounds the stereo. There is a small panel that comes off and you can feed the wires through there. From that point, I had the carpet pulled up so I could run the wires under the dash and out the same hole as the stock wire harness. Sorry, not pics of it. Its wired in, but I don't have the plumbing part done as I'm about to pull the N/A motor and put in a TII.
#5
Senior Member
Thread Starter
Join Date: Sep 2003
Location: vancouver, canada
Posts: 286
Likes: 0
Received 0 Likes
on
0 Posts
well ive been dealing SCATHCART with this alot and my system plans are as such:
-NOS wet system
-Single stage set up jetted to 50hp for now
-Electronic bottle valve opener
-Purging system out the windshield
So ill be having a master arm switch, purging switch and the bottle opener switch. I saw the one done by Dave Wilson (FC3S.com) where he mounted them on the coin boxes near the security light.
how do u take that plastic cover off by the way. the Haynes says pry it off, but im afraid it might break
-NOS wet system
-Single stage set up jetted to 50hp for now
-Electronic bottle valve opener
-Purging system out the windshield
So ill be having a master arm switch, purging switch and the bottle opener switch. I saw the one done by Dave Wilson (FC3S.com) where he mounted them on the coin boxes near the security light.
how do u take that plastic cover off by the way. the Haynes says pry it off, but im afraid it might break
Thread
Thread Starter
Forum
Replies
Last Post